Find trusted local electricians in Outer East Melbourne

Mains powered smoke alarm faulty. Needs replacing. Hallway is high and requires a ladder.

I need a licensed A-Grade electrician to connect power from my garage to a backyard shed/office and provide Certificates of Electrical Safety (rough-in and final). Scope (Stage 1 – now) - Site check & plan – confirm route, protection and cable sizing. - Trenching – dig ~15 m across lawn from garage to shed to compliant depth (AS/NZS 3000), supply/install heavy-duty orange conduit with draw-wire and warning tape, then backfill. - Sub-main from garage to shed – pull and terminate cable from the garage power board to the shed entry (photos show current setup and route). - Rough-in inside shed – run circuits for: - 5 x power points (double GPOs) - 1 x lighting circuit for 4 downlights (plug bases/battens as you recommend) - Issue COES so I can plaster the shed. Scope (Stage 2 – after plaster) - Fit-off – supply & install a small sub-board in the shed with RCDs (power + lighting), fit off the 5 GPOs and 4 downlights/switch, test and label. - Final testing & COES. In place alredy - Garage supply: recently installed 25 A, 3-phase feed from the house main board to the garage by a licensed electrician with certificate (it has 25amp RCBO, see photos). - Cable on hand: approx. 15 m orange 5-core cable (see photo). MAybe can be used for baord to ground inside the garage as 15m is maybe 1 or 2 m short for trench. - Shed: timber studs open, foil insulation in, ready for rough-in; proposed board location is marked in the photos. You to supply - Conduit/fittings, warning tape, junctions/glands, sub-board and breakers, GPOs, switches, downlights/plug bases, earthing hardware, fixings, any additional cable, and everything needed to meet AS/NZS 3000 and Energy Safe Victoria requirements. Requirements - A-Grade VIC licence, ABN & insurance. - COES for both rough-in and final. Conditions - Flat lawn between garage and shed; path ~15 m (30 concretes of a food path only, no other places). Easy access and parking. Please quote

Need about 9 lights changed to down lights. Home is about 15 years old, so all switchboard etc will be complaint. Existing light photo attached. Price listed is per globe Please list your price, what downlights you’ll be using and relevant experience Located in Knoxfield

I need (1) smoke alarm check and compliance certificate issued as per VIC govt legislation for annual smoke alarm rental property check and (2) replace 2 x damaged powerpoints at the same property (see photos of the 2 damaged powerpoints) Please make your offer inclusive of all materials, labour, compliance certificate and airtasker fees

I am renting our my property for the first time and need an electric safety check for compliance and safety purposes. Property is empty. Located in Ferntree Gully and needs to be done by 10th Sept. Please provide a reasonable quote. I also have some electrical works to be done at my new property, which can be discussed later.

Need a licensed electrician to add a new power point at the round spot marked with the arrow under the TV. Hoping to get it done next Monday or Tuesday

Install 3 down lights add 2 power points remove fluorescent light

Full house rewiring, 3bed 1970s house. Remove old wiring & switches. New wiring via roof cavity or underfloor. ~20 lights, 25x mains connection, electric cooktop, double oven, external connection for heat pump, electric water heater heatpump, spare, gate. New switches and mains socket. Upgrade to 3 phase connection. Ready for solar, battery and EV charger. New main panel at new location on different sidewall

Electrician to install 3 new downlight.

Need the following 1. fit a light fixture in one room. 2. fix/refit 2 motion detector lights in the driveway. 3. Change the bulb of 2 light fixtures.

Looking to have licensed electrician to fit off 5 power points and install 2 power points in bathroom for led mirrors, more work to be considered afterwards

Looking for a licensed electrician to; - Disconnect and remove 6 batten lights - Rewire remaining 6 batten lines to one switch (currently all on separate switches) - Ensure all electrical in garage is to code Needs to be complete by 18 August.

One of my front lights It will trip and The lights on this line are all off. when I press this switch, (sometime) There is also the smoke alarm.need change battery.

I need an electrician to do the following works in my garage: 1- replace the old florescent lamp with two 40W LED batten light. I will pay $150 separately for the lamps. 2- Add a new power point in the other side of the garage. All the wiring are surface conduit wiring. In addition, there is electricity wiring around 1 meter away from the required place. 3- Check the earth connection of the existing power point as my charger gives earth error. I believe it is problem in the power point but if finding the problem and solving it took more than one and half hour. I will pay $100 for any extra hour.

Install a 5-pin socket, wiring to electrical box and upgrade RCD to support an electric vehicle charger on a dedicated 40A circuit breaker. Install 8x 90mm LED downlights and wiring in the ceiling of a single story home in the dining room area.

Replacement of outdoor power point. Does not need built in timer like the previous one, a regular one will do

I have removed couple of walls and need to relocate 3 to 4 power points of removed wall alao need to add 6 down lights

Need an electrician or handyman to replace two hardwired smoke alarms with new ones, which we will supply.

Job Title: Installation of 3x Ring Spotlight Cam Pro (Solar) – Two-Story Townhouse Location: Bayswater North, VIC Two-story townhouse – address to be provided upon job acceptance. Scope of Work: Install 3x Ring Spotlight Cam Pro (Plug-In) units, each with its own Ring Solar Panel. Preferred mounting locations are under second-story eaves – installer must have a ladder tall enough to safely reach and work at these heights. Cameras and solar panels are brand new and pre-charged. Cables will be routed according to best practice to maintain neat appearance and secure connections. Installer must bring all necessary tools, brackets, fasteners, sealant, etc., to complete a clean and secure installation. Requirements: Proven experience installing outdoor Ring cameras, especially the Spotlight Cam Pro with solar panels. Familiarity with Ring’s product specifications and installation process. Product Page Installation Guide: https://ring.com/gb/en/support/articles/cr9u7/Physically-Installing-Spotlight-Cam-Pro-Solar?utm_source=google&utm_medium=cpc&utm_campaign=pmax&gad_source=1&gad_campaignid=20930702809&gbraid=0AAAAADI_e5szY4DoUvdrUBgUk1XFsfeB2&gclid=Cj0KCQjwgIXCBhDBARIsAELC9Zi1JTudYXMvXI-pPjV06vAwLsDk17m0qBEmWbJnGfd7T_Ea4zr0UDsaAk1nEALw_wcB Confident working at height and complying with safety standards. Must verify Wi-Fi signal strength at install locations (if required). Assist with app pairing and testing live view once physical install is complete. Timing: Installation date is flexible but ideally within the next [insert your timeframe – e.g., 7 days]. Expected job duration: 1-2 hours depending on access and complexity. To Apply / Book: Please provide: Examples or photos of previous outdoor Ring camera installs. Confirmation of required tools and ladder. Your availability. Flat rate or hourly quote (specify which).

I'm in the middle of a kitchen demolition and I need someone with electrical knowledge to disconnect an old oven and cooktop (pictured). I just want the electrical part taken care of, I will handle the rest.