Find trusted local electricians in East Melbourne

I have two new pendant lights that I would like to install in the ceiling. To replace down lights. This will require cutting the plaster to place the new lights.

I have a 2002 Gsxr 1000 mechanically sound ive just replaced wiring harness off a 2001 but kept my 2002 ECU for the main sensors i have the 2001 ecu if needed as thats all i could find there compatible ecu pinout is the same i have power lights everything bike turns over im not sure if I need one of the ecu remapped for ignition to work as I have 12v to the fuel relay and.pump but im unsure cause im a chef not machanic No need to bring ur tools if u dont want as I have all the tools needed from multimeter automotive testers, wire strippers solder and soldering irons, heat shrink and more, the paper is just a start so can come to terms or agreement

Looking to relocate a few powerpoints (and nbn cable if possible) to make arranging my network area much easier) I would arrange the plastering of the original locations. additionally I am wanting to install a powerpoint to conceal cable (pic 3) I also have cables in pic 4and 5 which i wish to conceal (they are powered by USB A Finally theres 1-2 additional power points i would possibly be interested in

We need the connection from heat pump to isolation switch it’s 18 kw pump and would need appropriate wire may be 2 meters to complete the connection

We have 2 downlights not working. Tried to replace them - no luck. Maybe they need a new transformer(?)

Fixing switch board and installing a new switch board

Replace MR16 downlights along with transformers for the entire house, downlight 32 count to be replaced with 240v LED downlights.

Need a ceiling pendant light install centred to the dining table. Expecting dining table delivery on 3/11 I recently had an electrician install some outdoor lights on the outdoor deck (adjacent to dining) and had some holes cut up in the ceiling. The holes provide access to run ceiling cables and into the walls to link up to the switches. Currently two gang switch (pictured before the recent work done) which needs to be further upgraded to three-gang. Offer needs to include the new switches as well Lamp - see as pictured Three way switch - as pictured

“The ceiling lights in my house are too dim. I would like to add 10 downlights.”

Replace a broken double power point. Domestic property. All parts supplied. No drilling needed. See photos. This afternoon if possible, or Sat afternoon (20th) between 12-3. Located in West Hawthorn.

Need a new electrical outlet installed in a bathroom

Need to replace 2 hard wired smoke alarms normal ceiling height

We need a GPO to be installed on the outside of our brick home, near the electrical meter box (as shown in the photos). This is so that we can later install a bluetooth sprinkler controller. Let me know if you have any questions.

Garage wall has Circuit Box. Not far (1M) I require a new circuit with a four plug power point, All on the same wall of the garage which is located in the basement. Need to run cables in the wall as assume there is not a ceiling cavity. Domestic home, 5-6 years old. Need certificate for new circuit. Licensed Electrician.

I need the current light fitting removed and replaced with a new light fitting I have purchased. Both lights are hard wired in so I need a certified electrician.

Old flat, standard height ceiling. Two living room ceiling lights and two bedroom ceiling lights. Assess one other light for safety. Plenty of street parking. Flexible timing, super early or evening is ok.

Need to remove 5 pendant lights in Victorian home and replace with new pendant lights (which we have ready). Need to saw 20ml of length of rods on each light.

Need to remove old ceiling fan and switch and install supplied new ceiling fan with supplied new switch

1 x light switch slightly sunken in (still works) - can be fixed so no longer sunken? AND 1 x broken power point switch needs replacing

Hello, We have the following light fittings that need to be installed: 1. 2 x 2-head circle led lights on each bedside of our bedroom (replacing existing pendant lights) - see first pictures 2. 1 x entry hall 3-head “flowers” light fitting to replace existing pendant light 3. 1 x chandelier style bedroom light fitting to replace existing. See pictures. Ask any questions. May be 2 person job. Light fittings are light (not heavy) but one or two might be big. The latter photos are of the existing fittings to be changed. Thanks