Find experienced local carpenters in South East Perth

I am looking for a cabinet maker/carpenter to build a mid-century style floating wall system with cabinets and shelves. See below for example.

Tenant has advised me of some issues with the property. It Needs new kitchen drawers (X4). The old ones are in bad condition and one is missing for some reason. And 4 other doors in the kitchen to be adjusted so they close properly. Thanks heaps

Carpentry and some tiling

Need assistance with some carpentry around the house

If you are any good at painting there is a small room to do first, or i can sort that. Then I need some small shelves designed and built, hang some other premade shelves, hang a mirror, all in gyprock walls. Would you be up to designing and building in a little corner unit afterwards too? Can be a seperate job.

Kaboodle Cabinet installation required in laundry, current cabinets will already be removed only installation required.

The roof had leaking which is now fixed. Looking for someone to fix the leaking stains at ceiling.

I am replacing an older electric under bench oven with a new one. The new oven is approx 100mm bigger (height). Require kitchen cabinets adjusted to suit. Note: Measurements on marked up image are taken using an app and are approximate Experienced trades only. Please provide examples of workmanship.

Can be one hour or two Basically need someone with a framing nail gun and a reciprocating saw Hand with a frame and cutting some timber out

I have existing kitchen cabinets that need to be removed and replaced with new cabinets I’ve purchased from IKEA. I’m looking to start the work as soon as possible

Cut down the brick along half wall in kitchen so that height is even with cabinets. <50 mm needs removing. 2500mm length. Currently topped with a temporary piece of skirting (glued/sealed in place).

Timber framing floor frame exterior cladding interior Gyprock and fix internal ceiling to suit. I don’t know what this would cost so I just put $1000

I have 4 cuoboards, each should have 2 to 3 shelves each

Supply instal corner cabinet kitchen door

Looking for assistance to make space for the dishwasher installation and make/cut holes for hoses for connecting dishwasher to the tap(no plumbing work required). Here are the pictures for your reference. Possibly need to completely remove the drawers to make space for dishwasher and also trim the other cabinet door to make appropriate space for installation. Primarily, make space as attached in Photo3 and make holes to allow connection to hoses. 1st and 2nd are current state photo. Possibly would like as highlighted in 4 & 5th photo which needs trimming in order to make space. Please give me a call if scope of work is unclear or have any doubts.

Need to install shelves and cover with sliding doors in the laundry

Carpenter or handy man needed to fix timber roof

Decking requires sanding and filling cracks and then staining

Need wardrobe door tops gently planed and then capped with pine timber stripping( doors were cut lower and exposing internal stuff ). Doors also need extra hinge added to top of both doors (needs wood router for the hinge hole), as they are a bit loose. Need an MDF panel (1440mm W x 535mm H x 16mm D) mounted and securely screwed above wardrobe doors. This is painted and ready to go up. Must be today due to a deadline. Must be an experienced handyman/ cabinetmaker/carpenter who is qualified, punctual, professional and efficient. Most of the work has been done so it's just touching up work on the doors and help securing the panel mounted and screwed into the timber, as it needs to hold an aircon unit 15kg. I have a small work bench and clamps on-site. What you need to supply: 2 wardrobe cupboard hinges, a planer, a wood router, timber stripping 25mm wide x 713mm long per door, and wood glue. Timber screws that can either be drilled through the mdf into the timber frame, or used in 90 degree angle brackets. If you are organised and efficient estimated work time: 90-120min max.

We have a built-in cabinet above our fridge comprised of an open shelf in the top half, and smaller storage partitions in the bottom half for wine bottles. FYI, the whole unit does not appear to be particular well secured. We want to reduce the height of the bottom storage partitions (or remove that row altogether?), to create additional space so that a new, taller fridge can be accommodated underneath. There is currently 1782mm of clearance from the bottom of the built-in cabinet to the floor. This needs to increase to at least 1810mm. We’re indifferent as to whether the existing cabinet is amended/reused vs a new replacement supplied, so long as we can gain the extra height we need for the new fridge, the colour is similar enough, and the thing is structurally sound and properly secured.