Find professional window and door services in Darlington

Our laundry room door has cracked and absorbed water, causing it to warp. It no longer closes properly. I have attempted to repair the crack, but the door is still warped and will likely need to be replaced. The existing door measures approximately 620 mm wide x 1940 mm high, so a standard-sized door may need to be cut or shaved down to fit. The task would include: • Supplying and fitting a suitable replacement door. Needs to be for Outside and we like the current style. • Cutting or trimming the new door to the required size • Taking away the old door, or cut into pieces for disposal Please include in your offer whether materials and disposal are included.

Front door locking mechanism is held in place by a single screw and has come loose, which means it is misaligned and doesn't work. The actual lock works fine though Need a solution that more securely keeps the lock in place on the door

Replace wooden door frame that has been damaged. Plane an d hang door replace door handle and latch

Moving out of my rental Front and back fly screens for repair or replacement due to dog scratching

Replace existing awning brick wall ground level 3m high

Metal security door frame has two anchor bolts loose. Need 2 x new dynabolts installed to anchor metal frame to brick wall.

Partially installed panel garage door that needs an expert to complete

Sectional garage door that has been fundamentally fitted by my carport installer. Need help with finishing

Supply and fit internal fire rated door And frame 795 x 1900 Accredited

Have new hardware, door completely off right now...ikea furniture

LG 420 Litre Bottom Mount Refrigerator I need the doors swapped. Currently the hinge is on the right side and I would like the hinge on the left side.

I have 4 western red cedar outdoor chairs, 3 need the support 'beams' replaced, and probably one dozen new slats. I would prefer to get them repaired rather than throw away, but don't want to spend a fortune. I have attached a photo. I will repaint them once they are fixed. - Due date: Flexible - Ideally I would have them by Sat 4 November

I’m getting some screen doors installed on our upstairs balcony, but the phone line currently runs through the bottom of the door sill and will block the screen door from opening and closing properly so I need it relocated out of the way. I think it could be sunk lower into the sill so it is out of the way. Need someone to think through and implement this. Thanks. - Due date: Flexible

Please check the installation guide online before bidding! https://level.co/support/level-lock-plus Install level lock+ onto door frame; replacing existing night latch preferred. Must be a neat job. - Due date: Flexible

The back of our property currently has a electric garage door. The motor has worn out and needs to be replaced. I would need someone to attend the property, identify a like for like replacement of motor and then install and test it. - Due date: Needs to be done on Saturday, 15 April 2023

Right door will not close, because the bottom of the door - Due date: Flexible

Our sliding door is broken! There's a front metal slider that the door is meant to clip into/hang off of (as shown in photos), but we can't get it back in the holes. Also, when I feel the top of the door frame, it appears only one nail or knob is there when I feel like there should be two? The back metal slider works fine, it's just the front one that's come unattached. As a result, the door scratches the ground and makes an awful sound when it's opened unsupported. - Due date: Before Thursday, 23 February 2023

Hi there I need help re hanging metal doors. Currently they are set up as sliding doors, sliding together right to left. I’d like them re hung on hinges swinging inwards so the entry can be used as a drive way (there is existing ramp). Ie it opens fully. This will include 🚪 finding hinges and installing to the frame and doors possibly via welding 🚪 removing or disabling the motor connected to the doors that enables them to slide 🚪 fitting a lock or bolt My idea is that they will be opened manually however open to stage 2 of the job which could be repurposing the motor or installing a new one so they open mechanically. Pictures enclosed. Quote requested to be confirmed via a visit before job is confirmed. - Due date: Before Friday, 19 August 2022