Find professional window and door services in Camberwell VIC

Fix the detached shower screen door

I bought a smart door knob from China, but don’t have the right tools to install it. Hoping to hire someone who knows how to do this. Also, I’m looking to install an extra hinge on the door too, as it is slanting downwards, hoping the hinge will pull it back up

Looking for someone to fix this broken wooden door. See the photos attached. I have the paint to repaint it also. I would like it to look good as new, preferably without replacing the whole door.

I need to fly wire door re-flywired. Good job for a handyman.

The door is stucking to the carpet, needs to grind from the bottom to make it smoother .

The rubber seal under my shower door has come loose. Need to reseal or replace this to ensure no spillage from the shower.

We have a pocket/cavity sliding door that is not sliding on its track and needs adjusting to slide without scraping against the frame.

We need a dog door installed in a French sliding door. There is a panel on the right that stays stationary for it to be installed in.

This handle doesn’t work anymore and needs to be replaced. It is loose and gets stuck.

Repair hole in right wardrobe door, patch small dent, put left door on hinge, repaint patches.

I have a deep cavernous gap between the brick wall and timber door frame at my front entrance (exterior side only) that needs filling and sealing. Job requirements: - Clean out any loose debris, dirt, old mortar - Brush out dust (wire brush or stiff brush works well) -Use compressed air or a vacuum to get deeper debris out, ensure dry surface. - Fill gap with expanding foam (low-expansion type). - Trim foam once cured. - Install backer rod. - Apply exterior-grade polyurethane or MS polymer sealant. - Finish with smooth, weather-resistant seal, for clean appearance and proper insulation. Looking for someone with experience in this type of repair who has the proper materials and can ensure a professional finish. The gap is quite deep so expanding foam will be necessary before final sealing. Please provide quote including materials. Photos don’t capture how cavernous the gap is, but it was enough for 3 spiders to call it home and I’d like to avoid that situation from re-occurring.

I have 1 wall and 2 door damages to be covered up, to make sure the damage is not visible! Thank you :)

I have a phobia of spiders. Please get rid of the big one at my front door Update: I went to take a photo of the 8-legged nightmare, but I think it disappeared into the void between the bricks and door frame

Strike plate needs adjusting. Bolt not sitting smoothly

Sliding door stopped working, seems like the door is now detached from the top hangers

The door is not going up and down properly

Supply and install solution to fix draft coming through door (235 x 82) between garage and into property. Sealing of the door frame edges and the 2.5cm gap at bottom of door.

Remove & replace hinges on a 2 piece, 2 metre high, bifold pantry door. Full overlay hinges provided.

We have an old door hanging in an archway (see photos) and we would like to close this off and create a new door arch (and hang a door we already have) next to it.

The bottom edge banding on two overhead cabinet doors above the cooktop has warped from heat. The door faces are fine. I only want the bottom edges re edged. Do not quote to replace the doors. Scope; 1. Remove both doors, protect benchtop and splashback. 2. Cleanly cut back and remove the warped underside wrap only, leave the front face intact. 3. Prepare the underside edge, square, clean, and lightly sand for adhesion. 4. Supply and fit new plain white heat resistant ABS or PVC edge banding to the underside of both doors. Use hot melt or equivalent cabinet grade adhesive. No contact film. 5. Trim and flush both faces neatly, radius the arris lightly, seal the ends to prevent lifting, and clean any glue residue. 6. Reinstall and align the doors, check clearances to the rangehood and the neighbouring door, and confirm soft close works as before. 7. Leave the area clean Notes. • The repair is to the underside edges only. The colour can be plain white. A close white match is fine as the new edge is on the underside. • Bring 16 mm and 18 mm white edging so the job can be completed in one visit. Measure on site to confirm. • Location is an apartment kitchen near Camberwell Junction. Photos attached show the exact edges to be repaired. Onsite parking available. Requirements for the Tasker. • Cabinetmaker, shopfitter, or handyman with proven edge banding experience. • Provide a tax invoice if required. Please answer in your offer. Confirm you will re edge only, not replace the doors. Confirm you will use heat resistant ABS or PVC edging and cabinet grade hot melt or equivalent. Confirm your availability and parking needs.