Book a trusted oven repair and installation expert in NSW

Connected an oven and install some power points

Loose hinge and oven door facia

Hi I need someone to please remove my existing oven and install the new one thank you you must be licenced thanks

I Waldorf gas stove oven. When we turn it on in the morning, a lot of fire comes out.

Issue: * When I switch the oven on, a “Fault” message appears and the oven does not start. * Initially, when the fault message appeared, the oven would eventually come on after approximately 10 minutes. * The problem has progressively worsened and the oven now does not come on at all. * The oven light also no longer switches on. * The gas cooktop burners/elements are working perfectly normally. * The issue appears to be isolated to the oven.

We have a Bosch oven HBF134EB0A We put it in the garage during the renovation and now it won’t heat up properly, only gets to about 130/150 degrees. Is it worth fixing?

New oven and cooktop needs connecting- fit off. Dedicated Circuits and cables already installed.

I need someone to disconnect an old oven and grill from my cabinet . Not sure if it’s hard wired or plug in so prefer someone with experience in this . In your response , let me know if you have done something similar before or not .

I need to replace as existing gas cooktop 90cm with a new one

Disconnect and un-instal old Smeg oven and replace/connect/instal new Smeg oven in same position under the kitchen bench

Need this full size oven opening made smaller to fit a smaller compact oven. I need the top of the oven housing to be lowered as I need more open space above the new oven to store my coffee machine.

Sorry I am being told multiple conflicting information from multiple companies so would like to see if the following is possible based on a recent suggestion from a company who looked at all our cables and breakers. They said we could safely hardwire our induction 4.6Kw to the existing 20A oven breaker and relocated our 2.3kw oven to a powerpoint nearby as the oven was originally a plug that got hardwired. Other circuit nearby is on 20A breaker. The existing oven cable is apparently a 2.5mm cable. It would be to hardwire AND install induction cooktop onto our bench (hole is already correct size) and add plug back to oven to connect to nearby powerpoint. May need a small hole drilled into the inside cupboard to get to the powerpoint but it is right next to the oven (length of cable may not be long enough to go into the existing hole at the top). Thanks If this is possible we’d like a quote on this. Thank you.

Please collect the new oven from St Ives and bring it to Freshwater. Remove the old oven and install the new one. Dispose of the old one. New oven weighs about 100kg. The new oven has been used and will be disconnected ready for collection. Access is ground floor with no steps at both locations. Please allow to connect gas and electricity or clarify if you can’t. Date: in mid August. 1st image is the old oven, second image is new oven. Both are 90cm wide.

We are having some modifications done in our Kitchen to install a small cutlery drawer above our microwave oven (as a separate Airtasker Task). However, for that task to go ahead, we need to ensure the Power Point to our Microwave Oven does not clash with the new drawer to be installed. The current Power Point is in the top left hand corner of the enclosure, we require it to be moved downwards by about 100 to 150mm. I think the Power Outlet is surface mounted to the back of the enclosure, and from what I can tell, the power cable comes into it from the cabinet wall on the left hand side, which is the sink enclosure.

We got a new electric oven. We just need our old oven disconnected and reconnect the new oven. Photos are of the old oven. Located in Penshurst, NSW

uninstalling the old oven and replacing it with new oven on 3 July between 7AM - 8AM

We have an oven that is hard wired into the wall. We have purchased an oven that has a plus. We need it converted.

Need to replace 60cm induction cooktop and oven underneath. I have ordered new ones. Need electrian to install both.

Licensed electrician needed to disconnect a hardwired freestanding electric stove/oven and reconnect a new like-for-like replacement on the existing circuit. Straightforward swap, no new wiring needed. Summer Hill NSW 2130 Must be licensed with valid NSW electrical licence Certificate of Compliance (CCEW) required on completion Flexible on timing, weekday pls Please include your licence number in your offer. Thx

We need a gas oven connected - see images. And a dishwasher hose with Aquastop valve fitted to a De Llonghi dishwasher. Must be qualified gas fitter and able to do both jobs. Easy parking, ground floor house in Bondi.