Find a local Tasker to set up your firewall in VIC

Firewall Replacement and Meraki Installation in a Medical Centre 1. Locate the Network Room / Rack ○ Identify and access the main network room or equipment rack at the clinic. 2. Identify Devices to be Replaced ○ Locate the Fortinet Firewall and the 4G failover device – these will be removed and replaced. 3. Locate Ubiquiti Switches ○ Find all Ubiquiti (Unifi) switches and AP onsite. ○ Note down the MAC address of each Unifi switch and AP. 4. Pre-Installation Photos ○ Take clear photos of the following before making any changes: ■ Network rack/setup ■ Fortinet Firewall ■ 4G device ■ Unifi switches with visible MAC addresses 5. Contact Us Before Proceeding ○ Please call the number provided in your job email before starting the replacement. 6. Install the Cisco Meraki Firewall ○ Replace the Fortinet with the Cisco Meraki firewall. ○ WAN/Internet port on the Meraki should be connected as follows: ■ If FTTN, connect via the existing modem. ■ For all other NBN types (e.g., FTTP, HFC), connect directly to the NBN NTD using an Ethernet cable. 7. MAC Address for IP Reservations ○ Once you provide the MAC address of the Unifi switch, we’ll configure the IP reservations remotely from our end. 8. Post-Installation Confirmation ○ Once the new setup is confirmed to be working, take clear post-installation photos of the final setup. 9. Label and Return Decommissioned Equipment ○ Label the Fortinet and any other removed devices with the clinic name. ○ Pack and ship the devices to the address provided in your job email. 10. Troubleshooting Support ● If the service doesn’t come up or there are any issues, please stay onsite and call us for troubleshooting support. We’ll assist you step by step

Firewall Replacement and Meraki Installation in a Medical Centre 1. Locate the Network Room / Rack ○ Identify and access the main network room or equipment rack at the clinic. 2. Identify Devices to be Replaced ○ Locate the Fortinet Firewall and the 4G failover device – these will be removed and replaced. 3. Locate Ubiquiti Switches ○ Find all Ubiquiti (Unifi) switches and AP onsite. ○ Note down the MAC address of each Unifi switch and AP. 4. Pre-Installation Photos ○ Take clear photos of the following before making any changes: ■ Network rack/setup ■ Fortinet Firewall ■ 4G device ■ Unifi switches with visible MAC addresses 5. Contact Us Before Proceeding ○ Please call the number provided in your job email before starting the replacement. 6. Install the Cisco Meraki Firewall ○ Replace the Fortinet with the Cisco Meraki firewall. ○ WAN/Internet port on the Meraki should be connected as follows: ■ If FTTN, connect via the existing modem. ■ For all other NBN types (e.g., FTTP, HFC), connect directly to the NBN NTD using an Ethernet cable. 7. MAC Address for IP Reservations ○ Once you provide the MAC address of the Unifi switch, we’ll configure the IP reservations remotely from our end. 8. Post-Installation Confirmation ○ Once the new setup is confirmed to be working, take clear post-installation photos of the final setup. 9. Label and Return Decommissioned Equipment ○ Label the Fortinet and any other removed devices with the clinic name. ○ Pack and ship the devices to the address provided in your job email. 10. Troubleshooting Support ● If the service doesn’t come up or there are any issues, please stay onsite and call us for troubleshooting support. We’ll assist you step by step

Firewall Replacement and Meraki Installation in a Medical Centre 1. Locate the Network Room / Rack ○ Identify and access the main network room or equipment rack at the clinic. 2. Identify Devices to be Replaced ○ Locate the Fortinet Firewall and the 4G failover device – these will be removed and replaced. 3. Locate Ubiquiti Switches ○ Find all Ubiquiti (Unifi) switches and AP onsite. ○ Note down the MAC address of each Unifi switch and AP. 4. Pre-Installation Photos ○ Take clear photos of the following before making any changes: ■ Network rack/setup ■ Fortinet Firewall ■ 4G device ■ Unifi switches with visible MAC addresses 5. Contact Us Before Proceeding ○ Please call the number provided in your job email before starting the replacement. 6. Install the Cisco Meraki Firewall ○ Replace the Fortinet with the Cisco Meraki firewall. ○ WAN/Internet port on the Meraki should be connected as follows: ■ If FTTN, connect via the existing modem. ■ For all other NBN types (e.g., FTTP, HFC), connect directly to the NBN NTD using an Ethernet cable. 7. MAC Address for IP Reservations ○ Once you provide the MAC address of the Unifi switch, we’ll configure the IP reservations remotely from our end. 8. Post-Installation Confirmation ○ Once the new setup is confirmed to be working, take clear post-installation photos of the final setup. 9. Label and Return Decommissioned Equipment ○ Label the Fortinet and any other removed devices with the clinic name. ○ Pack and ship the devices to the address provided in your job email. 10. Troubleshooting Support ● If the service doesn’t come up or there are any issues, please stay onsite and call us for troubleshooting support. We’ll assist you step by step

Firewall Replacement and Meraki Installation in a Medical Centre 1. Locate the Network Room / Rack ○ Identify and access the main network room or equipment rack at the clinic. 2. Identify Devices to be Replaced ○ Locate the Fortinet Firewall and the 4G failover device – these will be removed and replaced. 3. Locate Ubiquiti Switches ○ Find all Ubiquiti (Unifi) switches and AP onsite. ○ Note down the MAC address of each Unifi switch and AP. 4. Pre-Installation Photos ○ Take clear photos of the following before making any changes: ■ Network rack/setup ■ Fortinet Firewall ■ 4G device ■ Unifi switches with visible MAC addresses 5. Contact Us Before Proceeding ○ Please call the number provided in your job email before starting the replacement. 6. Install the Cisco Meraki Firewall ○ Replace the Fortinet with the Cisco Meraki firewall. ○ WAN/Internet port on the Meraki should be connected as follows: ■ If FTTN, connect via the existing modem. ■ For all other NBN types (e.g., FTTP, HFC), connect directly to the NBN NTD using an Ethernet cable. 7. MAC Address for IP Reservations ○ Once you provide the MAC address of the Unifi switch, we’ll configure the IP reservations remotely from our end. 8. Post-Installation Confirmation ○ Once the new setup is confirmed to be working, take clear post-installation photos of the final setup. 9. Label and Return Decommissioned Equipment ○ Label the Fortinet and any other removed devices with the clinic name. ○ Pack and ship the devices to the address provided in your job email. 10. Troubleshooting Support ● If the service doesn’t come up or there are any issues, please stay onsite and call us for troubleshooting support. We’ll assist you step by step.

- require an onsite visit to connect a Cisco Meraki firewall - require a long network cable (estimate 30 meters) - you will have remote support available from senior engineer - need to take a laptop as may need to login to device for testing - take a screw driver kit also just in case - basic IT experience will be beneficial - Due date: Flexible

FTTN Network with Telstra Router Telstra Business 1 x Switch 1 x Wall Rack 1 x Network Camera All setup - just require to add Sophos Firewall XGS 126 - Due date: Flexible

I will by the hardware and software required. I need a firewall / WAP / printer set up for a new office in the city. - Due date: Before Saturday, 28 May 2022