Find trusted local electricians in Parramatta

I need to install the down lights in my outdoor poach. I need around 6 downlights supplied and installed. Please share pictures.

Electrician to change 3 light switches. 1 x single, 1 x double, 1 x triple.

Supply and install external wall mounted double GPO, located approximately 3m from electrical meter box. Cabling to run under house so hidden externally.

Bathroom downlight not working. Replaced bulb, no difference. Sometimes when the switch is turned on, the light flickers. Have tried reseating into socket. May be issue with transformer? The cable is connected to SAL Mini Electronic Transformer.

New laundry extension - power is available Existing powerpoint is close Need a new 1x powerpoint 3 new down-lights (existing light already change to downlight) -2 separate switches for them

Ecogenica model Eg-215f, Failed capacitor or tripped safety switch issue. 15mm tempering valve has been replaced same issue. Recall for where the control panel inside the heat pump unit hasn't been touched just out of warranty 2yrs & 3 months now. Warranty 2 yrs. Need quote on repairs. Thanks in advance. Not a emergency situation.

I need help to fix 2 wall power points

Looking for a marine electrician to 1. fix existing wiring 2. change connections as they have rust on them. 3. connect brake light on trailer. One side only 4. Add anderson plugs for easy charging. Other than anderson plugs and wiring, all other items to be supplied at extra cost once confirmed Feel free to make an offer

Need to install some down lights in front of the house

Replace 2 x bathroom extractor fans, replace 3 x batten light fittings, fix pond electrical fitting (in garden). We will provide the stuff (fans and lights etc). Happy to pay hourly rate.

Extension wiring/ additional power plugs

I want to install down lights for dance hall approximately 35 Sqm

Lamps and power plugs needed

I need to remove the 3x down lights in my bedroom. I have bought the fixture from Bunnings. Just looking for a sparkle to remove it from the ceiling and plug in the new one without any damage. It is a fairly easy job Note : There are 3 lights that need replacing.

Dual GPO Install for the area shown in the picture.

Looking for an experienced and licensed electrician or data cabler to install 1. Data Wall plate (2 Gang ) with running cat6 cable from NBN conn (approx 20m) to router. 2. Data Wall plate (4 Gang ) with running cat6 cable from router (approx 15 m) to study room 3. Install Electric power sockets for NBN box and router 4. No damage to wall or painting and all running cables will go through the single storey roof

Fujitsu air conditioner needs to be repaired

Licenced electrician needed for apartment. A few jobs needed to be done... 1) There are 3 old ducted exhaust fans that need replacement. One in ensuite, one in powder room, and one in laundry. The existing exhaust fans measure at 27cm and are square. They have an internal motor and are connected to ducting. 2) A new ducted exhaust fan to be installed in the second bathroom if possible of the same nature as the 3 replacement ones. Currently there is no exhaust fan in the ceiling of the second bathroom. 3) Placement of a light switch on the inside of the bedroom. Previous owners walled off a section of the living room to make a 4th bedroom, but did not do any electrical work. The current switch to turn the light on and off is on the outside wall in the living room. 4) Installation of power points. Continuation of problem above. There are no power points in the added 4th bedroom. We'd like there to be 2 placed. Room size is 3.5m x 2.2m. 5) Replacement of balcony light. Currently the balcony has a weak light and we'd like it replaced with one that can actually light the balcony properly at night. No materials or products have been purchased for this job.

No power going to the air conditioner - cannot turn it on. Turned off main power and aircon will not turn on since then

I have a simple job to replace 1 LED light. I have the replacement light (don't need to supply) already with power cable however the old light has a power driver without power point for me to connect to LED and hence will need this converted