Find trusted local electricians in Winston Hills

The panel for air conditioner needs fixing. Please see photo attached. The display doesn't work..

I have low voltage power circuit that can be converted into poser point to connect faoutain Buddha

Replace hallway light globe Replace downlight in bathroom Install new double spotlight infront garage (faulty sensor) Rangehood light

Supply and replace 1 led downlight. Note:Available tomorrow morning around 10am,thank

Gas water heater stopped working need to check and replace.

Looking for an electrician to: - Install a new power point in the garage wall. - Drill a hole​ in the brick wall next to it for the CCTV camera cable. I will supply the power point and cable, let me know if any other material is needed.

No power going to the accessories. Bilge pumps, Sounder and lights. Boat is a 1990 quintrex fishabout. Not sure cost to diagnose and repair so open to offers to take a look and repair separately.

4 off down lights for 1 bedroom

Supply and install external wall mounted double GPO, located approximately 3m from electrical meter box. Cabling to run under house so hidden externally.

Looking for a marine electrician to 1. fix existing wiring 2. change connections as they have rust on them. 3. connect brake light on trailer. One side only 4. Add anderson plugs for easy charging. Other than anderson plugs and wiring, all other items to be supplied at extra cost once confirmed Feel free to make an offer

Fix 2 downlights in the living room, and install 4 downlights in another room.

Install: 2x240v smoke detectors (replace existing 240v smoke detectors) 1xfront door light (replace existing) 1xpowerpoint (not a new location, replace existing wall plate) 1xreplace 4-gang light switch (replace existing 4-gang wall plate) All are new for old replacements due to age/breakage. No new wiring needed. No location changes of light, smoke detectors, wall switchers or power points. 1x

Hello, We are looking for a licensed electrician to diagnose and repair a faulty ceiling light at our retail store, in Winston Hills. The Issue: One of the recessed LED downlights in our main optometry/consulting room has stopped working. Consistent and proper lighting in this room is important for our daily operations. The other lights in the room are functioning correctly. Ceiling Height: approximately 3 meters The Job: The task is to repair the faulty downlight and restore it to working order. The scope of work will involve: 1. Safely accessing the downlight in the ceiling (a suitable ladder is required). 2. Diagnosing the cause of the failure (e.g., a faulty LED unit, a failed driver/transformer, or a connection issue). 3. Supplying and installing the correct replacement part. 4. Ensuring the new light matches the colour and brightness of the other existing lights in the room. 5. Testing to confirm the light is working correctly. Please see the attached photos showing the type of downlight. Requirements: - MUST be a fully licensed and insured NSW Electrician. - You must bring your own tools, including an appropriate A-frame ladder for a standard commercial ceiling. - Ideally, you will carry common types of LED downlights and drivers to facilitate a repair in a single visit. Location & Timing: Location: Winston Hills Mall, 180/190 Caroline Chisholm Dr, Winston Hills NSW 2153 (exact location will be provided once the task is assigned). When: Please state your availability in your offer. Please provide a quote for the complete job, including the supply of a standard replacement downlight/driver. Thank you.

assist the electrician to mount the conduit, cabling and electrical equipments etc

All the PowerPoint in the house stopped working suddenly. All the circuit breakers appear to be working normally.

Power is underneath here, need to pull twin and earth to install a gpo behind tv wall mount and aerial connection, Already have GPOs, cable, aerial outlet and brush wall outlets to pull HDMI through

Supply and in install 4 downlights in a bedroom

Hi guys. I need an electrician to help me check my power line. Last night. All sudden the whole power cut off for 1 second as I can see the light flash and then turn back on. Later we found a few power points stopped working. Need someone to help me find out the cause. Please let me know if you can help.

I need my TV wall mounted with the bracket I have purchased. I will also need the power point moved up behind the TV and wires all tucked behind the TV

There are currently NINE (9) 50W x 100mm dia. gimbal halogen downlights with 12V power supplies, controlled by three (3) individual motion sensors, installed in the eaves of our single storey home. We would like quotes to remove all 9 downlights, and to replace them with 9 x LED gimballed OUTDOOR downlights of the same size, and with equivalent or preferably higher lumens. ♦️NON DIMMABLE, SINGLE COLOUR WHITEST POSSIBLE♦️ Notes: 1. ⚠️The eaves contain asbestos, so the holes already in place to flush-mount the existing downlights should be used for the replacements. 2. The motion sensors will remain assuming they're suitable.