Find a reliable appliance technician in Lane Cove

Experienced handyman (better 2 workers) needed to overhaul an L-shaped polycarbonate multiwall patio roof. All premium replacement materials are provided by me (Laserlite H-bar/U-shaped gaskets, breather/sealing tapes). You provide tools and labor. Site Details & Heights: Roof Height: ~2.7m from patio / ~2.2m from raised garden bed. Ladders on-site: 1.7m A-frame and 4m multi-position ladder available. 10 Panels Total (11 vertical H-bars): * 1 panel: 0.84m x 1.85m (Far left, needs bad DIY redone) * 3 panels: 1m x 1.85m * 5 panels: 1m x 3m (Deep section) * 1 panel: L-shape transition junction **Scope of Work:** 1. **Disassembly:** Remove 11 aluminium H-bar caps and old gaskets. Shift panels as needed. **Crucial:** You MUST bring your own structural plywood/crawling boards to bridge the 1m timber beam gaps and walk across the 3m spans. Do not step on plastic. 2. **Clean & Dry:** Pressure wash dirt/algae from internal panel channels using a mild bleach solution. **Mandatory:** Use a leaf blower/heat gun to dry inside the hollow channels 100% bone-dry before sealing. 3. **Trim & Tape:** Top edges get white Sealing Tape. The current bottom aluminum trim is a single long bar causing buckling. You MUST bring an angle grinder/hacksaw to cut it into 10 separate short sections matching each panel's net width (leave 3-5mm expansion gaps). Apply mesh Breather Tape, fit rubber U-gaskets, and press cut trims over them. 4. **Reassembly:** Thread new gaskets full-length into the 11 vertical caps so they compress tightly against the bottom end-caps. Slide panels under house flashing and screw down tightly. **Tools You MUST Bring:** * Plywood / crawling boards (essential for 1m spans) * Aluminum cutting tool (Angle grinder/hacksaw) * Pressure washer & Leaf blower/heat gun * Cordless drill with 5/16" hex socket https://www.justritestore.com.au/assets/Brochures/2024.0689-Multiwall-Brochure-Update-2024web6485.pdf see this diagram

Our Smeg fully-integrated dishwasher (model DWAFI6314-2) won't stay closed. The plastic door catch/latch has snapped. It's the mechanical catch, not the electrical switch, and the machine is otherwise working fine. IMPORTANT: You must bring the correct replacement part with you on the day. The part is the Smeg door-lock assembly, part 690074493 (this exact part was fitted to this machine before, so it is confirmed). Your quoted price must INCLUDE the cost of the part, not just labour. Payment will only be released once the repair is completed on the day, so please do not book unless you will have the part in hand. If you arrive without the part, we will reschedule and payment will not be released. Looking for someone experienced with appliance/dishwasher repair to supply and fit the replacement door latch. - Please also check the door seal and latch area while you're there, as there's some corrosion up top from water getting into the latch pocket. - It's a fully-integrated unit with a cabinetry front panel, so please take care with the door, decor panel and hinges. - Photos of the rating label, the broken part, and the latch area are attached.

Need a handyman to regrout shower tile and replace a seal for dishwasher

Multi-skilled Tradie: Plumber & Electrician required： 1 change new tape and cold and hot flexible braided hoses,I bought a Kitchen Mixer Swanneck &Flexible braided cold and hot hoses already please change for me.2 decommission an old switch and install a blanking plate. please provide your plumbing and electrical license numbers before I accept your offer.

Hi, I need someone to help repair my dryer which is banging loudly. Can you tell what the likely problem from the video, and how much it would be to repair? https://www.youtube.com/shorts/W5ziro5dStA The model is Fisher and Paykel DE8060P2

Looking for an experienced handyman to help with two small jobs: 1. New Dining table assembly 2. Washing Machine Drain Hose is too short Need the drain hose extended or replaced with a longer one so it reaches the drain properly.

I need temp setting on my Rinnai gas heater to be increased (the water is not hot enough). The electronic setting had been increased. But the external valve may need to be adjusted. Can you help please? Thank you

Rebooking task between Kris and Steve

Need to unstack a washing machine and dryer. replace the washing machine with our existing one, re-stack, and move the old washing machine into the garage.

Miele oven temperature sensor light doesn't go off

Looking to get a quote for repairing/replacing the rubber seal inside my washing machine Additionally, an optional repair we are considering is repairing the LED screen where some of the parts of the numbers don’t light up. Could you please provide a separate quote for this too? Flexible on date as not an urgent repair Model: Haier HWF 75AN1 7.5kg washing machine

Install LG washing machine WV5 1208W

We would like our double dish drawer serviced. It’s making some strange noises

Fix F11 error ( could be water drainage fault, clogged drainpipe or similar) Making unusual noises and water is piling up at the bottom of the dishwasher,

I need your help to - remove the cupboard door - take out my broken washer - install a new washer - put the door back in

Our gas cooker will sometimes get stuck in clicking mode and we have to turn it off at the wall.

I used dishwasher detergent sheets last night in my dishwasher instead of the usual Finish tablets and suds came out onto the floor and the E15 error came up. I need someone to remove the bottom panel and dry out and reset the foam leak sensor.

referigerator Repair ( Hisense- model number - HRFTF326S) - Freezer compartment working , Lower compertmemt not colling - FAn and motor is not working

Commercial dishwasher not draining properly

Plumbing job best explained by photo. I want a smart solution to a Bidet Auto Loo Wash install....without cutting through marble etc