Hire trusted appliance installation services in Sydney Eastern Suburbs

I’m looking for a licensed electrician to complete the electrical installation of a large AOKE cardboard cutting plotter. The machine has two Redbo regenerative vacuum pumps (2.2kW each, 220–240V single phase) that connect through the supplied electrical control box. The control box needs to be hardwired into the building’s electrical supply and the system tested to ensure everything operates correctly. Scope of work: * Inspect the supplied equipment. * Hardwire the supplied electrical control box. * Connect and commission the two vacuum pumps. * Verify correct operation of the machine. * Ensure installation complies with Australian electrical standards. * Advise if any additional circuit protection or electrical work is required. Equipment details: * AOKE cardboard cutting plotter * 2 × Redbo regenerative vacuum pumps * Single phase 220–240V * 2.2kW (13.7A) per pump * Electrical control box supplied I’ve attached photos of: * The vacuum pumps * The pump specification plate * The supplied electrical control box Please only respond if you’re a licensed electrician with experience installing commercial or industrial equipment. If you’ve worked with CNC machines, routers, laser cutters, vacuum pumps or similar machinery, please mention that in your offer.

Install - Westinghouse 60cm Multi-Function Oven with AirFry Stainless Steel WVE6516SD Current Over has been already removed

I have an asko cooktop (60cm x 60cm) that I need to be installed instead of the existing asko induction cooktop that was shattered due to a large mug falling onto it. The cooktop is the same diminsions and same brand, but slightly different model.

We're looking to replace the rubber gasket on our LG washing machine, the previous one had a tear at the bottom causing a leak so we've acquired the new gasket part and need help installing it. LG 10kg-6kg Combo Washer Dryer WVC5-1410W

I purchased a dryer from marketplace and it’s broken. It turns on,however when I press play, it will either spin for 10 seconds before stopping, or it will make a humming sound and not spin at all. It will also make a clicking sound. It was programmed upside down by the previous owner.

Someone needed to install new gas fireplace and raise the wall so that the TV can hang above. Photos shows the wall and the gas connection point which is outside by doors see photos, Must have all necessary licences to do job and have positive reviews. This is gas fireplace https://illusionfires.com.au/products/esprit-62-inbuilt-gas-log-fire?_pos=4&_psq=esprit&_ss=e&_v=1.0

Looking for an electrician to install a new oven, really straightforward job, just needs wiring (see photos)

Hi there, we would like someone to please carefully clean our washing machine, which has dirt around the inside rim, and the dryer, and clean and service our automatic vacuum cleaner (a Deebot). The vacuum cleaner is likely to be the largest job as it will need to be taken apart and some replacement brushes put in (we have the replacements). It is not particularly difficult (I have done it before) but it is fiddly and time consuming to clean the individual parts. I think it would take about an hour.

Disconnect old heater. Install new heater. I have measured the cut out. The new heater fits. Change light fitting in laundry. I have the new light fitting.

Hi we’ve purchased a commercial bread slicer, Yasaki, and need someone experienced in the area to pick up the blade from Moorebank and install it in our bakery in Coogee.

Samsung SR318LSTC, fridge not working. The freezer is still operating however the coils at the back of the fridge don’t stay cold. It may be a faulty sensor as the coils do go cold once the temperature of the fridge rises and then turns off.

Wiring and electrical installation of MATMÄSSIG, IKEA cook top.

We have a oven to install

Install rangehood. For my apartment

Take off old oven and put in front garden and install a new oven

Installation of the following rangehood required: https://www.beko.com/au-en/home-appliances/built-in-range-hood/hood-telescopic-60-cm-brh60tw

Installation of a new oven in a kitchen and put the old oven in the the store room

Currently the rangehood recirculates air back into the kitchen. Would like a duct to be installed (using the existing rangehood) and vented so that the air is released outside. The duct will need to go to out, above the cabinets, to an external wall (double brick) or via the ceiling and out the tile roof. The external wall is approx 1.3 metres away from the range hood. The ceiling is approx 30 cm from the top of the range hood. See photos. There is access to the attic. Would prefer a round rigid 200 mm diameter aluminium duct. Please provide quote for duct into the: 1. Ceiling and out to the roof 2. External wall I have not bought any ducting. The roof is tiled.

Install and supply cold water inlet hose pipe on washing machine, the hose that come with the washer was too short