Find a reliable appliance technician in Maroubra

Looking for someone that can fix my dryer. Address Mulwaree Avenue, Randwick.

Washing machine is turning on, all the functions seem to be working but when I press start nothing happens. I think it may be something to do with the door not latching properly

The details are I need the stacking kit fixed onto my washing machine then a dryer lifted to sit on top safely. It’s a 55kg dryer so it’s heavy & it needs putting in place properly…..

Hi Airtaskers, I please need a qualified gasfitter, or suitably licensed plumber to disconnect and cap a standard gas connection to an oven with gas stovetop. At the conclusion of the job, I'll need a Certificate of Compliance as per usual for gas work. Reason for doing this is that the oven is being replaced by an oven with electric stovetop. Therefore, the gas connection is no longer required. Thanks, Alistair

Our dishwasher is displaying a fault to do with the draining

Our SMEG dishwasher isn’t closing and the pin came out (see photos)

Someone who could fixed E:08 code on a heat pump dryer. Pls supply any parts if needed, let me know how much.

Dryer information included below! Dryer seems to work for about 3-4 minutes then turns off even though clothes are still wet Multi-temp ED56 Auto Sensing Dryer Fisher &Paykel

We are replacing our current cooktop with an induction cooktop and the existing electrical setup is not suitable. At the moment, the current oven/cooktop appears to be plugged into a standard power point, so we need a new dedicated circuit / higher-amperage connection for induction

Its a Rinnai Avenger 25TR. Suddenly the panel is showing error code 70. Its not turning on Photo of the PCB attached Location is Maroubra

I have a pot burn mark on a laminate countertop. I want help to remove the imperfection. The worktop is Polytechnic and the colour is velvet shimmer Matt . Located Randwick

Starter needs replacing, pliers don’t currently work

Issue: machine powers on, starts normally, drains correctly at the beginning of the cycle, and makes the usual startup sounds for the first 2-3 minutes, but then seems to stop early and doesn't continue through the full wash cycle or properly wash dishes. No obvious blockage visible and drainage appears to be working. Looking for someone to attend site, diagnose the issue, and ideally carry out a straightforward

Help a desperate mum with a washer that doesn't work. The Samsung washing machine stopped working properly after I cleaned the drain filter. I put the cap back correctly and also moved the black emergency drain hose. Everything is clean, but the machine is not draining the water. The drum works normally, but during any wash program the machine stops after a while because it cannot drain. As a result, the door stays locked until I manually drain the water using the emergency hose.

I need a plumber to come and fix our dishwasher as it has water pooling in the bottom and not draining.

Gas heater closing off after 15 mins Gas oven not staying ignited when gas button is released Gas stove working

Take off old oven and put in front garden and install a new oven

Currently the rangehood recirculates air back into the kitchen. Would like a duct to be installed (using the existing rangehood) and vented so that the air is released outside. The duct will need to go to out, above the cabinets, to an external wall (double brick) or via the ceiling and out the tile roof. The external wall is approx 1.3 metres away from the range hood. The ceiling is approx 30 cm from the top of the range hood. See photos. There is access to the attic. Would prefer a round rigid 200 mm diameter aluminium duct. Please provide quote for duct into the: 1. Ceiling and out to the roof 2. External wall I have not bought any ducting. The roof is tiled.

Door seal of Fisher and Paykel front loader washing machine (Product: 92141, model WH8560P1)has torn and is leaking lot of water during wash cycle. Needs replacement.

I need someone that can repair this. I think is just a bad connection as sometimes depending on cable positioning it works.