Hire trusted appliance installation services near you

Need an accumulator installed into a mobile coffee van, already have the accumulator and some parts that came with, if need more can purchase if required. Require someone with plumbing experience.

need to remove old rangehood and install new one... recirculating only (no ducting), 900mm . Include disposal cost in quote if option is available.

Disconnect old oven and reinstall new oven, standard 60cm electric. New oven will be unboxed ready to go.

Outdoor bbq range hood installed, ducted through pergola with dektite and flashing

Hi, I had an old ceramic cooktop that has cracked. It was connected via a rewirable plug into 25-amp socket. I've removed the old cooktop and unplugged it.  That 25A socket is on a circuit protected by a 32-amp fuse and also runs my oven which is plugged into its own socket. I'd like to replace the broken cooktop with a new induction unit, but the model I'm looking at is hardwired only. Im assuming the existing 32A circuit and existing 25A socket can be reused.

I need an old 60cm recirculating rangehood removed and a new Westinghouse WRF610SA (fixed, recirculating) rangehood installed in its place. Because the rangehood sits directly above an existing gas cooktop, the installation requires some minor carpentry modifications to meet the legal 650mm Australian gas safety clearance (AS/NZS 5601.1:2022) — the current clearance is only 585mm. The job involves: Removal: Disconnecting and removing the old 60cm rangehood (recirculating setup). Shelf Adjustment: The mini cupboard above has a horizontal width of 60cm and a depth of 30cm. The internal base shelf needs to be unscrewed and raised upward by roughly 8cm to 10cm, so the final clearance to the gas cooktop is at least 650mm (please confirm this measurement before final fixing). Door Trimming: The two mini cupboard doors will need 8cm to 10cm cleanly trimmed off the bottom edge to match the raised shelf. Important tool requirement: Because the kitchen cabinets are laminate over particleboard/chipboard, please use a clean-cutting circular saw or track saw with a fine-tooth blade to prevent the laminate edges from chipping or splintering. Mounting: Securing the new Westinghouse WRF610SA onto the newly adjusted shelf and setting it to internal recirculating mode (2 carbon filters). Note: The new unit is a standard plug-in unit (no hardwired electrical work needed) — it plugs into the existing power point.

Remove old oven. Picture attached. Install new oven: https://applink.ikea.com/tY8M9r9M4w--30557040--au--en Help with carrying old oven to apartment’s garbage room downstairs (there are lifts). Must be licenced electrician.

Installation of a new hose reel. Can reuse 2 holes already drilled from the current set up.

I need you to pick up an evaporator fan from NT Appliance spares in Winnellie, then go to my unit in Moulden and install it. Four screws, clip in a plug and the job is done!

Looking for a licensed electrician to install an electric cooktop at Hoxton Park Road, Lurnea NSW 2170. The cooktop is already on-site, and there is no need to remove the old cooktop. Please refer to the attached photos. Job requirements: - Install the electric cooktop - Check cables and electrical connections - Seal around the cooktop Test and confirm everything is working properly Must be completed by Friday, 19 September. Please bring all necessary tools and sealing materials. When responding, please provide: Your quote/price Your electrical licence details Thank you.

Foul Smell from the gap or back side of dishwasher - disconnection , removal from its place, checking and reinstalling with all connections

I have a new Beko BRH70UX 70 cm undermount rangehood ready to install. Looking for an experienced rangehood installer/cabinetmaker to remove the existing rangehood and install the new unit. Scope of work: * Remove existing rangehood and dispose of old unit. * Install new Beko BRH70UX 70 cm undermount rangehood. * Existing kitchen has a gas cooktop, so installation needs to comply with applicable Australian clearance requirements and Beko installation requirements. * Existing cabinetry/shelf will likely need to be modified/raised to position the new rangehood correctly. * New Beko requires 150 mm duct connection (120 mm adapter also supplied). * Existing ducting is only 100 mm, so this needs to be replaced. * Ducting needs to be rerouted to the other side of the cabinet/duct path. * Please supply/install appropriate 150 mm ducting, joins, elbows, clamps and external connection as required. * Keep duct run as short/straight as reasonably possible. * Modify cabinetry neatly and securely around the new rangehood. * Connect to existing power point * Test rangehood/extraction after installation. * Clean up and remove rubbish. Rangehood: Beko BRH70UX Width: 700 mm Depth: 296 mm Height: 254 mm Cabinet cut-out: 665 × 265 mm Duct: 150 mm preferred Photos of the existing installation and new rangehood are attached. Please quote for labour + materials and clearly identify any additional costs. Looking for someone experienced with rangehood installation, ducting and kitchen cabinetry, rather than a basic appliance installer. Budget: $700–900 depending on the amount of cabinetry and ducting work required.

Hi - after an appliance repairer to fix oven handle and put together cupboard.

Check a Fisher and Paykel dishwasher as its not cleaning the dishes fully. Fix the issues and can negotiate fee if requiring parts etc.

I need a stovetop installed. It is the same model as the current one but I dropped something on the glass and broke it. I have the new stovetop so I just need an electrician to remove the old one and install the new one. It is an Esatto 60cm Ceramic Cooktop with Touch Controls

We just bought an Omega Rangehood . As our Kitchen was built before 2023 the distance between the cooker and rangetop is under 65cm. We need someone to trim the current cupboard and install the hood.

Help re install Hoover washing machine seal that came off.

Looking for a qualified electrician/appliance installer to disconnect and remove an old cooktop, then install a new Devanti 60cm Electric Ceramic Cooktop with Touch Control. Scope of work: Disconnect and remove the existing cooktop from the benchtop cutout Leave the removed unit on-site, I will dispose of it myself Install the new Devanti 60cm Electric Ceramic Cooktop (Touch Control model) Connect to existing electrical wiring/circuit Fit into existing benchtop cutout Test all touch controls and heating zones for correct operation Ensure unit is secure, sealed, and level

Hi, I am looking for a licensed electrician to reinstall a ductless, filtering island rangehood that was recently taken down during kitchen ceiling renovations. Appliance Details: Model: Elica Wave (Island rangehood) Weight: Approx. 12kg Mounting: Hangs from the ceiling via tension wires and is hardwired. Ducting: None. This is a recirculating/filtering unit, so no ducting work or external venting is required. Scope of Work:Securely anchor the base plate to the ceiling. Reconnect the existing electrical wiring (hardwired). Hang the rangehood unit using the tension wires. Ensure the unit is perfectly level and operational. Compliance & Requirements: Must be a licensed electrician.A Certificate of Compliance for Electrical Work (CCEW) must be provided upon completion. Price must be for the COMPLETE work (no hidden fees). Logistics:Located in Sydney CBD (2000).Secure parking is available inside the building. Max vehicle clearance is 2.0m (please ensure your vehicle fits).