Hire a trusted appliance repair service in Kilburn

issue with fan on roborock hoover and mop

Rangemaster Aspire Dual Lever Kitchen Sink Mixer Tap AI says: To fix a dripping Rangemaster Aspire tap, you will need to replace the internal ceramic disc cartridges. #### PART ORDERED #### 🛠️ Required Tools & Spares Replacement Valve Cartridges: A compatible set for the Rangemaster Aspire (such as the TapSparesUK Aspire Valve Cartridge Set or similar Tap Magician Aspire Cartridges). 2.5mm Allen Key (Hex Key) Cross-head Screwdriver Adjustable Wrench or Spanner (or a specialized recessed valve removal tool) 🔧 Step-by-Step Fix For a detailed visual guide on how to safely open the handles and exchange the valves on this specific faucet model, watch this instructional video: https://youtu.be/jspUqoLP5FY?is=SOf9g7rKjMhlaHFb Isolate the Water: Turn off the hot and cold water valves underneath the sink before starting. Open the levers to drain any residual water from the spout. Remove the Handle: Locate the small grub screw on the underside of the handle lever. Use your 2.5mm Allen key to loosen it, then pull the lever handle straight out. Take off the Adaptor: Inside the housing, you will see a plastic handle carrier/adaptor. Undo the retaining cross-head screw in the center and pull the plastic adaptor piece off the cartridge spline. Extract the Old Cartridge: The original Aspire cartridges are recessed inside the tap body and often feature two flat sides instead of a standard hex nut. Use your wrench (or a specialized dual-sided cartridge removal tool)

I believe that the belt has disconnected from the drum - may need a replacement - it’s a zanussi washing machine.

I think I cable came from back of the washing machine

The door of our dishwasher does not close, to repair this

Fix cooker beko I need a new cooker top fixed

Seeking a repair of lawn mower whcih doesnt switch on.

My Hisense washer-dryer shows an F17 error part-way through the drying cycle I need help from someone experienced in diagnosing and repairing washer-dryers

Sage barister express hot water and steam wond not working. no water coming through. could also do with a service, it's kinda old

Melitta Barista TS SMART (F85/0-10) not recognising the water tank. The machine fails to detect the water tank during rinsing and when attempting to make coffee. I’ve already tried: ∙ Removing and reseating the tank ∙ Cleaning the sensor contacts on both the machine and tank ∙ Checking the float moves freely ∙ Power cycling ∙ Running a descale cycle None of the above resolved it, so I suspect the water tank sensor on the machine side has failed and needs replacing. Looking for an engineer experienced with bean-to-cup machines (ideally Melitta) who can diagnose and repair on site. I’m in NW6. Happy to share photos or a video of the fault beforehand.

I’m looking for a technician to assess and repair my SMEG ECF01PGUK espresso machine (UK model, 1350W). Issue summary: Pump runs but cuts off after approximately 2 seconds. I need to press the espresso button 3–4 times to complete a shot. Pressure appears weak and crema is very poor. Full descaling cycle has already been carried out with no improvement. Machine heats properly and no warning lights are flashing. Based on the symptoms, it may be a pump or flow meter issue, but I would appreciate a proper inspection and quote. I’m located in NW6 (London). Please let me know: -Availability for assessment (home visit or drop-off) -Inspection fee -Estimated repair cost range (if possible)

Dishwasher won’t drain or turn on

Water is not coming into the dishwasher when washing. When you close the door it makes a draining noise.

The sage espresso touch barista machine won’t work through its grinder head properly and won’t descale either. Need a sage expert.

Bosch dishwasher water left in bottom. I have checked sump bit and outlet pipe but no blockage there. Dishwasher is built in so bottom panel may need to be removed if issue is the pump

Floor lamp has stopped working. Its rickety and was a bit off on assembly, so maybe thats why as it feels like the parts arent put together properly. We use a smart bulb and don't use the floor button, its on at all times.

Our washing machine keeps tripping the electrics when it is in the middle of a cycle. I have replaced the fuse which I thought had solved the issue but after a couple of washes the same issue started happening again and fusing the electrics. Model is Samsung WW90T554DAW/S1.

Getting 3-beeps error on my Hotpoint dishwasher

The washing machine has stopped producing heat, either in the wash or the drying

Fix slow-draining sink & washing machine H2O error. Looking for someone to diagnose and fix a slow-draining kitchen sink and a washing machine that’s showing an H2O error and not filling with water. The two issues may be related. Job includes: • Unblocking or clearing the kitchen sink • Investigating the water supply to the washing machine • Fixing the H2O error (no water entering machine) I have parking, thanks