Find professional underfloor heating installation in London

Central heating system not performing properly due to undersized pipework – uneven heating across the house. Looking for someone to: * Upgrade heating pipework to correct size * Supply & fit 8 new radiators * Balance and test full system Boiler is working – issue is with pipework and heat distribution. Please quote for labour + materials (or break down separately). Access to floor boards for upstairs and cellar to obtain access to ground floor pipes.

Room Details: Kitchen size: 5.16m (L) × 3.15m (W) Current floor: tiled Issue: mixed subfloor (concrete + timber) ❗ Current Problem: Half of the kitchen floor sits on concrete Other half sits on timber subfloor Timber section is now damaged/uneven Ant infestation has occurred from edges (likely via gaps under timber section) Some tiles are already lifting/damaged 🔨 Scope of Work Required: 1. Strip Out Remove all existing floor tiles Remove timber subfloor section completely 2. Subfloor Correction Replace removed timber area with solid concrete base Ensure entire floor is level across full 5.16m × 3.15m Apply suitable damp-proof membrane (if required) Ensure no gaps/entry points (fully sealed against pests) 3. Floor Preparation Apply self-levelling compound across entire floor (if needed) Prepare surface suitable for large-format tiles 4. Electric Underfloor Heating Supply and install electric underfloor heating system Include: Heating mat/cable Insulation boards (if required) Thermostat (preferably smart programmable) Must be compatible with tile finish 5. Tiling Install large format tiles (likely 1000x1000mm or 1200x1200mm) Full kitchen area to be tiled (under cabinets where possible or up to plinth – confirm approach) Ensure: Correct adhesive for large format tiles Minimal lippage (flat finish) Clean grout lines Include tile layout planning (centred preferred) 6. Finishing Grouting Silicone sealing around edges and units Ensure fully sealed floor (no pest entry points)

I need a cable installed for my underfloor heating mat in my shower room. Picture 1: shows the plug socket in the adjacent room, which I’m hoping you can run the cable from. Picture 2: shows the direction of the joists under the floor to help plan the route. Picture 3: shows the height where I need the cable brought up to feed through the wall so the thermostat can be installed on the other side. There is lots of room under the floor to pull the cable through

I need a plumber to check the boiler and heating system in a flat. It has not been used in over a year. Also, check for possible leaks in the bathroom.

The electric for my immersion heater has blown at the switch for the second time in a year suggesting there is a problem either with the wiring or perhaps the heating element in the tank.

1) Carefully remove all floorboards downstairs and set aside. 2) install timber battens between joists 3) install rigid insulation minimum 50mm thick between floor joist, above battens. 4) underfloor heating pipework installed between joists (materials supplied by us). Joists to be notched where required to allow pipework to pass through 5) dry sand a cement mix screed to the placed between joists above underfloor heating pipework and levelled flat. 6) fix down floorboards over the top of all, fixing floorboards into the joists.

1) There is no water pressure in bathtub shower of common bathroom 2) Flush tank of common bathroom toilet doesn't have pressure and needs replacement 3) Issue in couple of heating radiators (common bathroom, conservatory, en-suite bedroom, living room) which need bleeding or Drayton TRV4 valves to be replaced 4) The Aqualisa power showers in enclosed bath make a huge noise, need to be replaced

Hi, I need an urgent visit from a Gas Safe Registered engineer to fix my Vaillant ecoTEC Plus boiler. ㅤ Currently, we have no hot water. The boiler display is showing a pressure of 2.8 bar, which is in the warning zone. I have tried to reset the unit, but it is not firing up. ㅤ Requirements: • Must be Gas Safe Registered (please provide your ID number in the offer). • Experience with Vaillant ecoTEC models. • Task involves: Safely reducing system pressure, checking for a faulty filling loop or expansion vessel issue, and ensuring the boiler restarts correctly.

Bosch oven is turning on but will not heat up. Possible fault with the heating element?

Connect electrics. Theomostat and a Install a stat Must be qualified electrician

Toaster not heating up . Lights come on but no heat .

Looking to have filing loop replaced as leaks when tap turned to fill pressure

Electric oven (Bosch) turns on but does not warm up.

Supply and replace heating element for Sage Barista Touch SE880 Coffee Machine - Wimbledon. Flexible dates/times.

I need someone experienced to replace the heating element on a Rangemaster electric oven. I have already bought the new part so need someone to do the labour only.

So these came with a plug but it’s too short so I’m looking for a handy electrician to either hardwire this or replace the lead with longer lead to reach a plug. I have two of these btw.

Need a new heating element(s) for my washer dryer Haier IDW

Heaters connected to the Potterton gas boiler in the property are not working. New build flat (2020). Recent issue with boiler needing to be capped due to suspected CO leak, but this was resolved. Only seems to heat to 0.5 C.

This boiler is not working as it should and I was recommended to replace the heating elements. So looking for someone to do this... It's not heating water well or fast enough, it costs me insane amount of money (like summertime around £100 goes to just have hot water in the morning for one shower session). Now it provides barely warm water after 3 hours of heating water. I don't know price for this work so please do let me know how much materials and labour will cost!

Currently having some work done on my kitchen and I’m looking for a plumber/hesting engineer to remove the old bulky boiler filter and replace / possible slightly reposition with a smaller more compact filter.