Find a professional balustrading contractor in QLD

Hi tradies - im currently renovating a property for sale in Kippa Ring and ready to move on this if the quote is in budget (please provide supply and install quote), thanks Ryan. Double gates on the right side of the house: Opening width 2140mm. 2x gates 1050mm wide X 1080mm high Single gate on the left side of the house: Opening width 1780mm (fence post to house). Height to match double side gates. Front balcony balustrade: 2x 1650mm wide (sides) and 1x 7250mm (front) Front door patio balustrade handrail across width only: 4220mm wide All single slatted - 65x16 vertical slats spaced at 40mm to sit below 75x25 aluminium handrail - all powdercoated aluminium in Dulux Lexicon.

I need about 5.9 lineal metres of s/s wire balustrade installed/fitted. I can supply all the materials. To be fixed into steel RHS posts. 1 @ 3.5 wide and 1 @ 2.4m width. x 900 high. Would need to have experience with this system preferably.

I need a balustrade built on my front deck. The front of the deck is 4.2m wide. The first picture is the deck. The second picture is the remaining balustrade to replicate. I would also like fibre cement attached to the front of the deck to cover the bearers and beam that are visible.

There are broken balustrades on a verandah (estimated 6 metres) - I have started pulling it apart and sanding back the bits that are good but the job needs to be completed, put back together and painted (nails and paint already here)

Hi, I need a handyman or carpenter to install a timber balustrade/handrail for my outdoor stairs. ​I want it to look exactly like Image 2. ​What I have:7 New posts (already erected) ​Your job: Cut and install the handrails and vertical balusters between the posts. Must bring your own tools (mitre saw, etc.) for angled cuts. ​Note: NO PAINTING REQUIRED. ​Location: Carindale

Need new glass balustrade The deck is approx 1.5 over ground level. Is pool height fence still required?

Looking for an experienced carpenter, deck builder or balustrade installer to install a 316 stainless steel wire balustrade system on my front deck in Eagleby, QLD. Materials supplied by me (Chaindirect - Balustrade Basic Kit (No.6) – Turnbuckles (33), Wire (150m), Fittings, Tools Kit): 316 stainless steel wire balustrade DIY kit 3.2 mm 1×19 marine grade 316 stainless wire Turnbuckles, end terminals, saddles and all fittings Hydraulic swaging tool and cable cutters Work required: Remove and dispose of the existing timber balustrade infill only (existing timber posts and top rails to remain). Install stainless steel wire terminals and cables. Tension all wires evenly. Ensure the installation is straight, secure and professionally finished. Clean up and remove all waste upon completion. Project details: Approximately 7 railing sections 8 horizontal wires per section (56 wire runs total) Total railing length approximately 12 metres Existing timber posts and handrails remain Stainless steel wire system only (no glass) Requirements: Experience installing stainless steel wire balustrades. Own tools (other than the supplied swaging tool and cable cutters). Please provide photos of previous similar work. Installation must comply with Australian residential balustrade requirements. Please include with your quote: Your experience with similar installations. Estimated time to complete. Total labour cost. Any questions after reviewing the attached photos. Location: Eagleby QLD 4207. Must visit in person to confirm the full job and understand work. Budget: Looking for quotes.

Replace rotten lower hardwood balustrade rail only x2. Existing post is sound. Reuse existing balusters if possible. Supply matching hardwood, install, prime all cut ends. Painting not required. Price negotiable

We have just raised the height of a balustrade beside a set of external stairs through on-site steel welding. The task now is wire brush the welds to remove any rust and scale, prime all new weld joints and then to paint the balustrade black (monument). This only applies to the new, raised section of the balustrade. The photos show the that balastrad looking down and then looking up as well as a typical welded joint that need to be prepared. The photos also show the lower balustrade already painted black and needing no further work and the new upper work which has been primed grey. There is also some new infill bars in the old section shown in the photo looking up the stairs that need to be painted.

The bottom section of veranda post has rotted as well. Veranda post is 95 x 95mm. Also a section of balustrade needs replacing consisting of a section of horizontal and vertical dowels.

Timber base board and uprights have rotted. Need a qualified handyman to be able to remove the base boards (two of them) and then replace all of the uprights including the three long ones in the middle, finally replacing the base boards with new timber Price negotiable and suitable timber will be supplied with your guidance.

Install aluminium balustrade inc. collection from Bunnings We need someone to collect and install an aluminium balustrade. Materials purchased by us upfront — you will not be out of pocket at any point. What you need to do: - Collect ProtectorAl aluminium fencing components from Bunnings (we will purchase and arrange) - Install on site: 2800mm straight run + 1000mm return at 90°, mounted to top of masonry wall (approx measurements). - 4 flanged posts dynabolted to masonry, 3 panel sections (2 panels cut to size between pickets) Tools required: hammer drill + 10mm masonry bit, angle grinder or hacksaw for cutting aluminium, level, basic hand tools. Materials: Purchased by us upfront Please check the photos before quoting.

Experienced carpenter required to repair two balustrade/handrails that have rotted on our front outdoor stairs. Materials and labour must be included. Quality hardwood must be used.

We are moving house and need someone to please instal some wire for the Balustrade/Deck. We have the wire. All holes are already in the timber, all measure ready to go :) This is quite urgent so would love someone in the next week or so to complete this.

Need these steps and balustrade painted and grip tape strip added to edge of each step after. Balustrade has been sanded but the steps will need a light sand, paint and grip tape supplied

I am after a painter to paint balustrade Timbers before I cut and install them. And also paint already installed balustrade, I have already got a coat on the installed Timbers. $45/hr cash 8 hr day

Remove this decorative balustrade and bricks. We have a council waste voucher for this.

Supply and install 3 x wire balustrades.

Repair or replace either or both of the two timber units, post and or that part of the balustrade - not sure if and what can be fixed or needs replacing altogether. Scott of work is provide advise. Time, effort and tools required for job. Anything need replacing I will reimburse separately. Cheers

I am in need of someone to come and install glass that we have on the front porch of our house. There are 4x spaces: 1 - 2715mm wide 2 - 1640 wide 3 - 1765 wide (this needs to have a gate in it) 4 - 1870 wide We have glass already and spigots to fit. If any extra glass is required we will pay for this separate to the price