Find a professional balustrading contractor near you

removing the balusters and putting back similar but upgraded meterial.

I need about 5.9 lineal metres of s/s wire balustrade installed/fitted. I can supply all the materials. To be fixed into steel RHS posts. 1 @ 3.5 wide and 1 @ 2.4m width. x 900 high. Would need to have experience with this system preferably.

I need a balustrade built on my front deck. The front of the deck is 4.2m wide. The first picture is the deck. The second picture is the remaining balustrade to replicate. I would also like fibre cement attached to the front of the deck to cover the bearers and beam that are visible.

wire balustrade installed on an outdoor deck. My preference is 6 wires but I’m happy to be led by you if you feel we need less/more. You will need to provide all materials. I have included the second image for a reference.

I need the wire balustrade repaired on the deck

There are broken balustrades on a verandah (estimated 6 metres) - I have started pulling it apart and sanding back the bits that are good but the job needs to be completed, put back together and painted (nails and paint already here)

This balustrade has rusted out and needs a new piece welded in on site. We are in Darwin city.

Stair balustrade to be painted (light sand, primer, gloss white x 2 coates). Perspex will be removed

Replace rotten lower hardwood balustrade rail only x2. Existing post is sound. Reuse existing balusters if possible. Supply matching hardwood, install, prime all cut ends. Painting not required. Price negotiable

We have just raised the height of a balustrade beside a set of external stairs through on-site steel welding. The task now is wire brush the welds to remove any rust and scale, prime all new weld joints and then to paint the balustrade black (monument). This only applies to the new, raised section of the balustrade. The photos show the that balastrad looking down and then looking up as well as a typical welded joint that need to be prepared. The photos also show the lower balustrade already painted black and needing no further work and the new upper work which has been primed grey. There is also some new infill bars in the old section shown in the photo looking up the stairs that need to be painted.

Timber base board and uprights have rotted. Need a qualified handyman to be able to remove the base boards (two of them) and then replace all of the uprights including the three long ones in the middle, finally replacing the base boards with new timber Price negotiable and suitable timber will be supplied with your guidance.

Install aluminium balustrade inc. collection from Bunnings We need someone to collect and install an aluminium balustrade. Materials purchased by us upfront — you will not be out of pocket at any point. What you need to do: - Collect ProtectorAl aluminium fencing components from Bunnings (we will purchase and arrange) - Install on site: 2800mm straight run + 1000mm return at 90°, mounted to top of masonry wall (approx measurements). - 4 flanged posts dynabolted to masonry, 3 panel sections (2 panels cut to size between pickets) Tools required: hammer drill + 10mm masonry bit, angle grinder or hacksaw for cutting aluminium, level, basic hand tools. Materials: Purchased by us upfront Please check the photos before quoting.

Install a frameless standoff glass balustrade using materials I supply on site. Balustrade is located more than 5m above ground level, so it must be installed and certified to AS 1288 / AS/NZS 1170 by a suitably qualified and licensed tradesperson. Materials on hand: • 15mm frameless standoff glass panels: 850W × 1280H ×6, and 750W × 1280H ×3 • Summit 30×21mm Nanorail Deluxe handrail 5800mm (satin) ×2 • Summit Nanorail Deluxe rigid glazing rubber 2900mm ×3 • Summit 30×21mm Nanorail Deluxe wall plate extended (satin) ×6 • Summit 30×21mm Nanorail Deluxe 90° joiner (satin) ×1 • Glass standoffs 38×25mm (satin, SS2205) ×48 Note: fixing rods are NOT supplied — please include any missing items in your quote. Scope: • Labour-only install of the above into the existing structure, glass 15mm toughened with Nanorail top rail fixed into structure • Confirm supplied standoffs and fixing details suit 15mm panels for a balustrade above 5m per AS 1288 before commencing • Flag anything missing or any recommended change to the fixing approach prior to install • Provide a Certificate of Compliance on completion from a licensed/qualified trade, expressly noting the balustrade is more than 5m above ground Requirements: • Appropriate trade licence and insurance — please state licence number • Quote labour only; advise availability and lead time Site: inner Sydney. Please confirm you can certify to AS 1288 at this height before quoting.

Experienced carpenter required to repair two balustrade/handrails that have rotted on our front outdoor stairs. Materials and labour must be included. Quality hardwood must be used.

Front of House Balustrade and back balcony Balustrade - total of Approx. 18 - 20m. Simple straight line balustrade (to be painted black). Paint will be supplied - need someone to prepare, prime and paint before the 1st May 2026 (latest 5th May). Any questions, just ask. Would love the help. Thank you!

I’m looking for an experienced tradesperson to install a stainless steel wire (cable) balustrade on my internal staircase. Holes are already drilled and aligned

We are moving house and need someone to please instal some wire for the Balustrade/Deck. We have the wire. All holes are already in the timber, all measure ready to go :) This is quite urgent so would love someone in the next week or so to complete this.

Need glass balustrade around the edge of the decking. Frameless glass, 900mm-1m high. Thanks guys

Need these steps and balustrade painted and grip tape strip added to edge of each step after. Balustrade has been sanded but the steps will need a light sand, paint and grip tape supplied

We need glass created and installed by an experienced glazier to the top window above our front door and to the balustrade next to the set of stairs that takes you to the rooftop of our house. Window measurements 880mm by 345mm Balustrade measurements 1750mm by 1750mm triangle