Find a professional awning contractor in Melbourne

Its a motor and remote operated Awning and extends full. It just needs to be realigned and adjusted to the correct position as one side is tilted downword and its low on full extension. Pleaes quote. Thanks

See images. Take down old 'awning' (I'll get rid of it) and put up new one (motorised). I'll deal with the electrics separately. Also, put up a small, simple blind in the kitchen. This is it more or less - https://www.bunnings.com.au/instahut-retractable-folding-arm-awning-motorised-sunshade-4-5mx3m-grey-white_p1161177

Looking for an experienced trade painter to repaint the exterior architectural trims, gables, and fascias of a single-storey weatherboard home in Thornbury (see attached photos). Scope of Work: Front Facade: Paint front gable trims/battens, window awning/hood, timber window frames/sills, and lower plinth baseboards in a heritage muted olive green (per mockup image). Rear Facade: Paint rear roofline fascias, gable cladding/trims, window/sliding door perimeter trims, and lower baseboards. Side Laneway/Path: Paint metal/timber fascias, gutters, downpipes (changing over from burgundy), and lower baseboards along the side pathway. Prep Work: Light sanding, cleaning down surfaces, scraping loose paint, and spot priming where required. Materials & Requirements: Paint (Supplied by Painter): Painter to supply premium exterior acrylic paint (e.g., Dulux Weathershield or Taubmans All Weather) tinted to agreed olive/green trim colour (e.g., / Olive Leaf). Equipment: Painter to supply all brushes, rollers, masking, drop sheets, and ladders/step platforms. Access: Flat, clear ground access at front, rear, and side brick pathway. Please state your experience with exterior timber and metal trim painting and include links/photos of past work when submitting your offer.

Hi! One of the locking pegs (mushroom pins) on my awning window frame has sheared off. Details: Hardware Brand: Kin Long window system (aluminum frame). The Issue: The pin snapped off, leaving the rivet/fastener base stuck in the track. What's Needed: Drill out/remove the broken fastener shaft and supply/install a replacement peg/pin to match the existing one (photos attached). Parts: I do NOT have replacement parts. Tasker must supply the replacement pin/screw/rivet. I have attached photos of the intact pin for reference, the broken base, and the overall window setup.

Need a PowerPoint installed from inside to outside of a building in an awning

Awning has come away from house on one side and needs new screw/affixing. Will need ladder to access as it is up high.

I have two windows with timber frames, approx 82cm x 47cm each that I would like to replace or repair with crank windows to get more air flow into the bathroom

Need a new awning, new fabric

We are having a full cassette awning installed at our property into an area with cladding. We have a temporary GPO within the cladding cavity which we need you to connect an external weatherproof black GPO on the cladding and potentially change the power wiring from the Awning unit to a black cable.

i have very old awning, the mechanism works but need to change the cloth. I dont have picture at the moment, but can provide if needed.

Sonfy retractable awning not responding to remote have changed battery on remote assume it’s a motor issue please help

I need an experienced handyman or awning installer to install an outdoor awning at my restaurant. The awning has already been purchased and is on-site. I need someone with the appropriate tools and experience to securely mount it to the building. If you have previous experience installing commercial awnings, please mention it in your offer. Location: [Carlton VIC 3053] Flexible with date and time.

Install awning, similar to supplied pic (that one from manufacturer, Outrigger Awnings). Job requires: - Marking, levelling, drilling 24x10mm holes, install using masonry screws. Manufacturer recommends drilling 8mm holes first, then expand to 10mm. I have the masonry screws. - Install, tension, drill and rivet awning as per manufacturer's instructions. - Bring experience and advice on the above. Second pic is installation site. The wall has a downpipe, which will be accommodated by installing the batten slightly away from the wall (this has been discussed with the manufacturer). Total size of awning is 6.2m (along wall) x 2.6m. Awning is delivered and ready to be installed. I figure this is about one day for two people (builder plus 1). I can also assist.

I need an acrylic sign to be installed on the awing of a shop front and then also removed will need an extendible ladder as it is about 4 metres height

After the remote controlled motor of the awning stopped operating the canvas of the awning began to tear and the awning needs to be replaced. The awning is at rear of the house with access restricted to wheelbarrow width (about 70cm).

Description: I need an experienced carpenter or builder etc to replace the damaged awning fascia panel on the front of a shop entrance (see attached photos). The part that requires replacing is circled in RED. Scope of works: 1. Remove and dispose of the existing damaged fascia panel 2. Supply and install a new fascia panel (suitable exterior material) to replace the part that is missing, and the part that is damaged (circled in RED). 3. Prepare and paint the new panel to match the existing building colour/finish 4. Ensure a clean, professional finish that blends with the current façade and is SECURE. Requirements: * Must have experience with exterior building repairs/cladding/fascia work * Must supply all materials and tools * Must colour-match paint as closely as possible *Must provide a tax invoice on completion!

Hi - my retractable awning on my balcony has jammed with a tangled rope. I need assitance fixing this. I suspect we will have to unfix the awning, pull it down to ground level, and then untagle the rope and put it back up. I am on the 3rd story, have access to a full sized ladder, and I am willing and able to be a set of hands that help. Thanks, Tom

Hi, I’m looking for an experienced installer to replace the fabric on an existing folding arm awning at a café. Details: - Location: Carlton - Width: approx. 4.4m - Projection: approx. 2–2.5m - Existing arms and frame are already installed and working - New fabric will be supplied (custom-made) Scope of work: - Remove existing fabric - Install new fabric onto roller - Ensure proper tension and alignment - Test opening/closing mechanism Requirements: - Experience with awning installations (important) - Own tools and equipment - Ability to handle commercial-sized awning Please provide: - Your quote - Relevant experience/photos of similar work Flexible with timing but looking to get this done soon.

I have an awning that I want installed on the wall of my house I have assembled it, but its too large to manage on my own. The awning is 3.6m long. I'm happy to assist with lifting it to mark up and then mount as required. The wall of the house is Hebel. I have a selection of fittings that should be enough for the install.

I have a van with an awning but it’s too small so I bought a bigger one to install. I want to then move the smaller awning to another van i have. Both have roof racks to attach to