Find a professional gyprocker contractor in Sydney

I have a hole in my gyprock in Petersham and my MIL has a hole in her gyprock that has covered the brick in Newtown. The 2 holes are similar size but I only have a photo of the one in Petersham. I need it patched but I can paint them myself.

I need Gyprock installed into my 2.5m x 3.5m shed. A timber frame has been put up, with blocking and 600mm studs. The shed has a sliding door and a window, a 10mm gap has been left around those for the Gyprock. We’re wanting a square set finish around the door, window and ceiling (no cornice). The job is to install the gyrock, sand and patch - ready for paint. We already have the Gyprock and the corner bead here ready to go.

MASCOT not Rockdale. I want to partition upstairs from downstairs. There is currently a stairwell that goes up to the main part of the apartment. There is a solid balustrade that I would like a wall built on top it all the way to the lower floor ceiling. At the base of this new wall I need a lockable door installed, the door should be solid(external rated) and as large as possible the distance between the bottom of the stairs steps and main wall is 950 mm x 950 mm. It will be possible to remove some of the balustrade dressing to make this door at least 920 mm. Framed up sheeted and painted.

Plumber had to break through two tiles and the wall behind it in order to fix a leak. Now I need that fixed. I have the tiles you need, but you would need to bring everything else. See images for before and after.

Need to install a 1.8m long company signage on a gyprock wall. No tools on site, power outlet is nearby the installation area.

Airtasker Job: Gyprock + Furring Channel Work (Ready for Paint) I need a gyprocker to complete the following works: 1. Pelmet + Blind Concealment • Install furring channels and steel studs along the ceiling line. • Build a pelmet structure to fully hide a roller blind. 2. LED Feature Wall Preparation • On the section highlighted in the reference image, install furring channels behind the existing wall so the electrician can run an LED wire internally and keep it hidden. • After the electrician completes the wiring, return to sheet the wall with new gyprock. Finish Required: • All areas must be plastered, set, sanded, and finished 100% ready for painting. Requirements: • Neat, professional framing and gyprock work • Ability to coordinate timing with my electrician Reference images can be provided to show exactly where the yellow and green sections need to be completed.

Help us hang a mirror securely onto the wall in our office. The mirror sits behind a glass door so need to make sure the floor door stopper is in the right spot and may need to patch whole in black stained floorboard if it ends up being moved. Or happy to discuss your ideas to ensure the door handle doesn't hit the mirror. Located in co-working space on William St. There is street parking directly out the front that we can cover the cost for. Just better to start early in morning to get the good parking spot, there are many other street parking spots around but will just be a longer few mins walk instead. Note there are no lifts (stairs only) but it's only one level up. Mirror details: https://www.freedom.com.au/product/24693714 Assembled Product Dimensions Width: 52 cm Depth: 4 cm Height: 190 cm Weight: 10 kg

See pictures. Need to repair. I am not sure if whole wall needs to be repainted. Let me know what you think.

I would like to get 3 ceiling fans (remotely operated with lights) installed where oysters lights are currently installed, all gyprock .One power point is lose in gyprock, needs repair/replacement. One light switch needs to be moved by about 40cm to a different position in wall.

Need to mound a 42 inch on a gyprock wall, I have purchased the Wall mount from bunnings

I have a damaged gyprock wall around a service shaft in a bathroom that needs to be repaired. Using aqua check as it’s in a bathroom

Looking for someone to: - remove the gyprock partition and architrave as pictured (waste can be left on site) - patch the rear wall as required where the partition was, and sand ready for painting (do not need to paint) - patch the ceiling where the exhaust fan is and sand ready for painting (do not need to paint) - install new floor tiles where the partition was. Spare matching tiles supplied. This part of the room is not waterproofed. Waste can be left outside as a skip bin for other work will be ordered in a few weeks. Many thanks.

We need an experienced mirror/glass installer to cut and install 3 large mirrors at our physiotherapy clinic. Each mirror already has the Z-clip attached, but we do not have the wall-mount brackets, so you will need to supply and install the matching brackets. Mirror details: • 3 × mirrors — 3015mm × 709mm, approx. 5mm thick • Mirrors already onsite (no pickup needed) • Installed using Z clips – top clip load-bearing, lower clips to keep mirror flat • Manufacturer measurements for clip heights and spacing provided Installation surfaces: • 1 × brick section • 2 × gyprock sections Installer must supply correct fixings for both. Scope of work: • Supply matching Z-clip wall brackets • Measure and cut mirrors if required • Install brackets at correct heights • Hang all mirrors flush, level, and secure • Ensure minimal bowing using additional clips Manufacturer notes: • Mirrors sit 5mm off the floor • Clips #2 and #4 are non-load-bearing (prevent bowing) • Diagrams of clip positions available Location: Strength and Pilates Physiotherapy G 103 Foveaux Street, Surry Hills (ground floor) Requirements: • Experience installing large gym/studio mirrors • Own tools, brackets, fixings, adhesive if needed • Ability to cut mirror cleanly • Professional finish essential

The removal of a burn mark on the kitchen bench and would like the surface restored back to its original color.

Hi, I’ve just demolished an internal wall and now need a gyprocker or plasterer to: • Patch and repair wall and ceiling gaps • Re-sheet and flush joins • Sand and prepare for painting There are some areas with exposed brick and framing that need neat finishing. I can send through photos for reference. Please let me know your availability, quote, and if you can come by this week for an inspection. Location: hillsdale

We need to have a 2.1m half wall plaster repaired at the edges and raised by about 5 cm, so it lines up with our kitchen cabinets for the upcoming stone benchtop installation

Jobs 1 and 2 are simple. Fill the holes with plaster and then paint over. Job 3 is more complex. Cut out the gyprock (may be fire rated gyprock, am not sure), replace-gyprock that square, plaster and paint. We will provide paint. Other materials provided by you.

I need gyprock installed to the lower third of an exposed brick wall to prepare the wall for installation of wainscotting. The section of wall to be covered is 270*90cm You will need to include all materials in the quote.

We need to install this table to a meeting room in the office. "The Wall Mounted Booth Table can be installed using a drill by itself, however, we recommend an experienced builder installs the restaurant table as you will need to ensure that the fixings are secured into solid timber in the wall. Each order comes with handy instructions too. " Length: 47.2″ (120 cm) Width: 27.6″ (70 cm)

1. Cut gyprcok wall (direct stuck to block wall) 2. Install 10 angles (needs to be level for 2x shelves) 3. Re-plaster around angles / set and sand ready for paint. Only materials supplied will be angles, fixings for angles and plasterboard.