Find an experienced ceiling fan installation professional in Sydney

- Install ceiling fan (remove pendant light and put fan in its place) - Replace two ceiling light fittings - Adjust height of two pendant light cords

When using the remote to turn on our Arlec ceiling fan, the fan doesn’t start and beeps twice. At first when the issue started occurring, it would start and then stop again repeatedly but now it won’t start at all. When turning on the light it switches on completely fine, it’s just the fan that won’t turn on. I’ve done some investigating on google for answers and the most likely explanation that came up was this: “With Arlec ceiling fans, this combination of symptoms—where the unit beeps responsively to commands but the fan itself remains dead—is a classic, known behavior pointing to a faulty internal remote receiver module (specifically the controller unit tucked inside the top canopy) or a dead starting capacitor. The electronics are registering your command (the beep), but the switching circuit inside the receiver is broken and failing to pass that physical electric current down into the motor windings.” This is a possible fix google said: “Replace the Internal Remote Kit: An electrician can drop the top canopy and swap out the broken receiver block. Arlec sells replacement modules such as the Arlec Remote Control Ceiling Fan Kit or the Arlec Grid Connect Smart Kit at retailers like Bunnings Warehouse.” If this is the problem, I can buy the kit at Bunnings and we would just need it installed on the fan. If interested, please message me on here.

Looking for an electrician to install a brand-new Arlec ceiling fan in a room. I have already purchased the fan. It is an apartment. Top floor. Roof access can be with our building manager. This is a fresh installation where no fan has been before. However, there are two existing lights situated on either side of where the fan will go. Job Details: • Fan Model: Arlec ceiling fan (No light, includes wireless remote control). • Wiring Needed: No wall switch wiring is required since it operates via remote.

New ceiling fan - has been mounted already. Just needs to be connected to the power supply. Hardwired smoke alarm close by will provide connection point.

Lights under the ceiling fan controled by remote control and switches on the wall do not turn on by remote control or switches. Does not seem to be a very complicated electrical issue. Need someone to have a look and to fix this minor issue. Thank you.

Remote controlled ceiling fan has stopped working.

Install of Nautica 132cm DC Fan with Light (remote controlled) in my studio apartment. Fan Blade Type - ABS No. Of Blades - 3 Fan Blade Size - 52in / 132cm No existing fan, just an oyster light. See image for light and install spot.

Timer on clothes dryer has stopped working and needs to be fixed. The ceiling fan/ light combo in the master bedroom has become slightly detached from the ceiling and needs to be re-secured.

Need someone with a ladder and the ability to neatly hook up a ceiling fan with light where an existing light is.

Needs to completed by a licensed Electrician

Hi, I am wanting an electrician for two tasks. One is I am wanting a light switch for a chandelier in a living room which is currently just on/off to have a dimmer added. Other task is in a separate room/light fixture and is to install a ceiling fan where currently a ceiling light fixture hangs. Re price, I’m pitching here for labour, I understand the hardware will cost extra, let me know if I should source prior to or you can

Looking for a licensed electrician to supply and install a simple, quiet and reliable white ceiling fan in my living room. There is currently a ceiling light in the exact location, which I'd like replaced with the fan. Preferably a 48–52" DC fan with remote control and minimal wobbling. Please include the fan, installation, GST and CCEW in your quote. I’ve attached a photo of the existing light for reference. The landlord has approved the installation subject to receiving a quote. Please provide your total fixed price and the fan model you would supply.

Hi, I’m looking for a licensed NSW electrician to complete several electrical installations in my apartment. I have not purchased the new fittings yet, as I would like the electrician to review the products/specifications and confirm compatibility with the existing installation before I place the order. I will also need to seek approval from the strata for the ceiling fans (I assume). Work required Living/dining area/bathroom - Remove and replace 2 existing ceiling light fittings with new LED light fittings and ideally a dimmer. - Replace 1 existing ceiling light fitting with a DC ceiling fan with integrated LED light. Bedroom - Replace 1 existing ceiling light fitting with a DC ceiling fan with integrated LED light with a dimmer. The ceiling fans will be installed in the same locations as the existing light fittings. No new ceiling locations are planned. The fans I am currently considering are the EGLO Surf DC Ceiling Fan with integrated LED – 48", White with Oak Timber Style blades. The ceilings are approximately 2.8 m high. 2 x 2 of the current lights are on the same switch so I think that would need some work to put a fan wall control (if possible) - See pictures Switches / dimmers I would also like the electrician to: - Check the existing wiring and wall switches. - Confirm what type of wall controller / dimmer is compatible with the new lights and ceiling fans. - Advise whether any switches or dimmers need to be replaced. - Let me know whether I should purchase these myself or whether you can supply the compatible ones. I would ideally like someone who can inspect the existing installation before I purchase the fans and lights, or review the product specifications and confirm compatibility beforehand. All new lights, fans and other fittings will be supplied by me, unless otherwise agreed. If I could have some quotes, that would be amazing. Thanks

Hi, I recently had a new ceiling fan installed, but unfortunately it stopped working the following day. It was working normally immediately after installation, but now won’t turn on at all. Looking for a qualified electrician/handyperson to come out, diagnose the issue and get it working again. As it’s newly installed, I’m hoping it’s something straightforward with the wiring, connection or controller. Photo attached showing the fan

Looking for an experienced plasterer/gyprocker to complete a small repair in the ceiling around a recently installed ceiling fan in our master bedroom. As shown in the photo, there is a rectangular section of plasterboard around the ceiling fan which was cut to install a support beam for the fan. The job is to: * Patch/reinstate the plasterboard around the ceiling fan * Tape/set/plaster as required * Sand smooth and flush with the existing ceiling * Leave the repaired area ready for us to prime and paint ourselves * Protect the bedroom/flooring from dust and clean up afterwards Ceiling height is approximately 3.9 metres, so you’ll need to provide your own suitable high ladder/platform/access equipment. Please include all plastering materials and access equipment in your quote. No painting required. Looking for a neat, professional finish with the repaired area flush and ready for painting.

I will purchase 5 ceiling fans with lights, I need the installed into 3 bedrooms and lounge and dining room area.

I’m looking for a licensed electrician to: • Remove the existing ceiling fan (pictured). • Remove/disconnect the existing Martec fan wall controller if required. • Install a new Temple & Webster Dancing Flowers Stained Glass 2 Light Pendant in the same ceiling location. • The pendant is hardwired, weighs approximately 5 kg, is 51 cm wide, and has an adjustable 100 cm cord/chain. • Please ensure the pendant is securely fixed to the ceiling and the existing decorative ceiling rose is not damaged. • Please include all labour and any standard electrical fittings/fixings required for installation. The pendant light will be supplied by me. Please let me know your total price, including Airtasker fees if applicable, and your earliest availability.

I would like 2 x AC ceiling fans replaced in the bedrooms. I can order 2 x DC ceiling fans. I would like the existing wall switch to remain. I don’t want a remote. Let me also know if this DC fan is not compatible with the existing wall switch.

Need a licensed electrician in Sydney to adjust wiring for ceiling fan/light switches. Currently there are two switches: 1. Low light 2. Main light + ceiling fan together I’d like it changed so that the fan is linked to the low light instead. Main light still needs to work properly. Please quote including callout/labour.

My bathroom ceiling fan just stopped working randomly yesterday. I removed the cover and it looks like something is blocking it, maybe dust. I need someone who can assess the problem, carefully remove the blocker and put it back up the way it was.