Find a fence installation professional in Inner South Melbourne

15metre long fence with 600mm plinth +2.4m fence palings installed. The council requirement is for the fence to come up to 1.7m above the finished floor level and the current ground is sloping down. No removal of old fence required as it is to be built in front of the current fence due to council requirements for the build. The current fence may need some support.

Replace fence (roughly 2m) with gate.

Timber, cement and gate ( plus latch )supplied. Total length of fence only 4m x 1800cm height. Must show experience of fence work or handyman skills.

i need to make out existing picket fence higher by extending pickets or replacing fence for a higher one

I need a colourbond driveway gate. Total opening is 4880mm, with a swing gate of 3400mm, the remainder being fenced. The height 1800mm. Also a side gate width 1250mm, height 1600mm. I might also want the garden fence about 20 metres done. So, I prefer an onsite quote.

I have an outside powder coated pedestrian gate with a broken hinge , the screws do not screw back into the frame , the hinge either needs to be replaced or repositioned. I have a new set of hinges if required

I need a side gate to be installed 1.2m approx at the side our house at the rear corner before the backyard. White or charcoal aluminium or timber flexible in all regards, just looking for a good sturdy and secure lockable gate.

Need a fence built, aprox 3.5 m. I have the wood as the last fence builder ran into problems. .

We have a long wooden picket fence and would like someone to add an approx 1m wide wooden pedestrian gate with hinges and key lock

I want to install some type of fence that needs to be atleast 100cms tall with no horizontal bars for my kid to climb on, on an opening that is 250cm wide. I checked all the readymade fences and they are too short in height and not sturdy enough

Looking for a practical handyman to install a lightweight side gate between two units in Hughesdale. The setup: -Gate and frame are already purchased and on site - One side has an existing panel/post to attach to - The other side needs a support — looking at a no-dig/concrete-free post from Bunnings (e.g. ground spike anchor) Measurements: Total fence to path width: 133cm Gate width: 78cm Side panel: 31cm Path width: 84cm Gate height: 120cm Back panel height: 124.5cm Front panel height: 124.5cm (approx.) What we need: Someone to assess, source a suitable ground spike or stake from Bunnings (nearby), and install the gate so it opens and closes securely. No concreting, no panels, no major earthworks. Goal: Keep a dog contained. Function over form — doesn’t need to look perfect. Budget is $200 all-inclusive (your time + any hardware). Happy to discuss if you have a smart, cost-effective approach. This is a job for a confident handyman, not a fencing contractor. If you’ve hung a gate before, this is right up your alley.

Remove current wooden fence approximately 32 metres and install/build a new wooden panel fence that separates two houses. Also replace a small section. Of a second wooden fence at one of the properties

9.6m Boundary fence plus a addituonal 1.5m intersecting fence 195cm needs to be removed and replaced. see photos.

Supply and install a glass pool fence. My quote includes the cost of glass. 1200*1000

A panel of my fence needs to be replaced. I need professional work to remove the old one, dispose of it, and install the new one (must also provide the new fence looking similar to the rest of the fence). Length 8m.

Front Fence Installation – Vertical Slat (aluminum)(10mm gap) + 2 Pedestrian Gates Looking for an experienced fencing contractor to supply and install a front fence for my client. Scope of Work: * New vertical slat fence * Approx. height: 1.5m * Slat spacing: 10mm gap * Finish: White (powder-coated preferred) * Include 2 pedestrian gates (one at each end of the fence) * Full installation required (posts, framing, alignment, etc.) Site Conditions: * No existing fence (clean install) * Easy access Measurements 1500w (gate) 1300w 950w 1270w 805w 1550w 3130w 1000w (gate) 3000w Important: * Do NOT include locks – electric locks will be installed separately * Gates must be prepared/compatible for future electric lock installation Requirements: * Must supply all materials and labour * Proven experience with vertical slat fencing * High-quality, clean finish required Quote must include: * Full breakdown (materials + labour) * Estimated timeline * Gate hardware details (hinges, latch provision only – no locks) This job is for a client, so I’m looking for a reliable subcontractor. Clear quotes and proven experience will be prioritized. The most qualified contractor will be awarded the job.

Install a colourbond side gate (measured and onsite ready). new Concrete path poured 2 weeks ago Need holes drilled and gate/posts fitted. see images

Money is for making cotact. No actual work reqired.. Need a timber picket fence installer. Preffered who know to drive forklift, and fabricate driveway gates. Can dress, shape, edge wooden posts (see post styles in photo). Run picketmachine We have a metal fabrication workshop. Looking for full time subcontracter Rate $45 + GST+ $5 into super. Essentially rate of $50 per hour ($45+$5) Role will be fence installation, working in the yard, driving forklift.

Money is for making phone contact , no actual work required. Looking for subcontractor who can install motor, dig tranch to take 24 low voltage wires to power point to the house. Few jobs every month. We fabricate sliding gates , swing gates etc based in oakleigh melbourne.

Fence: Timber fence approx. 36m long x 1.8m high Scope: Minimal repair only (no painting) What I need done: Re-fasten/secure any loose palings and rails Tighten/replace fixings where needed (screws/nails) Replace 3–6 timber palings/planks (max 6) that are damaged Make the fence solid and tidy, ready for painting later Clean up and remove any small debris off-site What’s NOT included: No post replacement / no re-levelling the whole fence No full fence rebuild No painting Budget guide (please quote accordingly): If you supply materials: Budget $400–$800 (include materials + pickup) Materials: You supply materials: You supply palings, fasteners, and any small consumables What to include in your offer:: Estimated time required Any assumptions (e.g., “up to 6 palings included”) Confirmation you have the tools to cut/fit palings and securely fix rails Timing: Flexible — ideally within the next 1–2 weeks.