Find trusted local electricians in Croydon NSW

Hi I need an outside PowerPoint moved to inside an outdoor kitchen, please see pictures attached. I posted a task this morning but given I needed to allocate it to one person it didn’t allow me to accept the electrician as well.

Need to fix a ceiling light

Replace: - 2 power points (single) - 9 power points (double) - 2 power points (double, low height of 45mm - see pic) - 1 power point (double) with extra switch (for fan) - 1 light switch (vertical) - 2 light switches (double) - 1 light switch (3 switches, including 2 dimmers - see pic) - Exhaust fan (replace - see pic) I will provide all the materials for the above. Also, provide under cabinet lights (to replace fluro) for: - 1.8m - already connected to 1st switch inside cabinet - 0.7m - to be linked to the 1st switch through 2 cabinets - 1.5m - already connected to 2nd switch on cabinet See pics. Please provide good quality under cabinet lights. If dimmable, will need to replace 1st switch to add dimmer.

The on/off switch of the PowerPoint is not working smoothly, and it feels slightly hot. I’m looking for someone to replace it.

Tue-Fri Qualified, experienced electrician for: 1. replacing ceiling fan, including removal of wall control (new fan is remote) 2. in laundry, change 1 power to 3 separate power points along different areas of the wall (for washing machine (single), dryer (single), and benchtop (double). 3. replace fluro light with different light fitting. Old house, so ceiling may be asbestos - must wear PPE.

We are looking for someone to help install a new air conditioner on the second floor of our home. The model of the new air conditioner is shown in the attached image, along with the specific location for installation. Additionally, we need the old air conditioner removed and taken away. Budget: $600–$700 Timeline: Preferably this week or next week. Please let us know your availability and experience with similar tasks. Thank you!

Laundry is under renovation. Power goes to laundry then outside. Need to re-direct so no power in laundry and stay under house to supply outside. Today if possible. Access under house - about 90cm clearance

I want to remove an oyster light from my bathroom and replace it with a single heat lamp and two downlights, and change the wall switch accordingly. I can supply the products but I'd like advice on whether what I'm planning can be installed in a two wire system. The products are below, but I'm happy to be advised otherwise if there are better options. 1no heat: https://www.martecaustralia.com.au/product/uno-single-heat-lamp-bathroom-heater/ 2no downlight: https://thelightingoutlet.com.au/products/90mm-led-downlight-13w-black-white-cct-cri-90-hcp-81x50113-havit-commercial?contact_posted=true#contact_form Switch: https://www.mjselectricalsupplies.com.au/connected-switchgear-geo-single-powerpoint-two-ext?gad_source=1&gclid=CjwKCAiA3Na5BhAZEiwAzrfagML0KxxBUDghZUMJ-rrLcVvtZIcq34vn6g0xzQe0Ign2X2P7hJdCLhoCW-kQAvD_BwE Dimmer: https://connectedswitchgear.com.au/our-range/switches-and-socket-outlets/mechanisms/dimmer-mechanisms/led-rotary-dimmer-300va-white/ I'm hoping the switch can have a dimmer for the downlights and a regular mech for the heater. Some very rough diagrams and photos of the wiring to the existing oyster light are attached and I can add photos of wiring behind the switch when home this evening. Thanks.

Need 1 light fitting replaced in laundry . Does not need to be the same type . Need 2 new power points for fridges . Please quote to supply and install. There is power near where the 2 power points are to be installed.

Need an electrician for 1.repositioning switchboard (upgrade the switchboard as it’s very old and bulky) 2. installing bathroom 3in1 heat fan light 3. adding 4 power points (2 has wiring at the back of the wall, another 2 has wiring close to the position) 4. change 3 lights

Qualified electrician please to: 1. Fix cabling of old telco connection (possibly still in wired for NBN) 2. Replace ceiling pendant light with a new one 3. Replace 3 power outlets with new ones

two existing telecom wall port need repair incl. NBN port. Townhouse, have own router ready, socket number received from ISP, just need to repair telecom wall port for plug in.

We have a primary need for an electrician supply and replace 2 existing hardwired smoke alarms which are interconnected as they are older than 10 years old. The current make is a Lifesaver, model LIF3000. Other tasks required are: -Swap out an external flood light. A replacement will be supplied. -Change 2 x GPO plates, as the switch has become jammed. A replacement will be supplied. -Recrimp and secure network cables at a particular wall as everything has become loose. -Replace an existing TV antennae socket that has become loose.

I have an LG B42AWY-7G6 ducted aircon installed together with an Airtouch 5 console. It does not work (Error code 3) and I need an AC technician proficient in both LG and AirTouch to come and help make sure it works correctly. - Due date: Flexible

LIGHTING Supply and replace 6led fluorescent tubes. Need a tall ladder 6 meter high. Internal. Property type - Office - Due date: Flexible

Install a light fitting/leadlight shade that has its own lights. - Due date: Flexible

Electrician needed to install a feature light for living. There is already an existing light fixture. The pendant is this https://www.templeandwebster.com.au/Blundell-12-Light-Metal-and-Glass-Pendant-TELX1743.html?refid=GPAAU447-TELX1743_200591161&device=m&ptid=&PiID%5B%5D=200591161&gbraid=0AAAAADzVgw3NQbtrnYeNZuNFnYRzxwDVk&gclid=Cj0KCQjwnP-ZBhDiARIsAH3FSRcSVVdELq8Wj5he4J6dT9vMnkEfm0eXbRnBoWrFGPJmtUit6rJbiz0aAnoHEALw_wcB

It is a two storey house and we have 24 panels that need the mesh installed to stop the birds going under. - Due date: Before Wednesday, 31 August 2022

Need a licenced electrician to remove old light fitting and fit new one. Would love to have this done tomorrow (Saturday 23rd) Thanks

Need an electrician to install 3 hand dryers at a site in Croydon, Sydney. Power points are available to plug into. Hand dryers need to be mounted and wired into PCB. Will require to remove old hand dryers