Find local air source heat pump installation & repair near you

Heat pump condensor unit out side the house to be disconnected for concrete pouring out side the perimeter of the house. Re-install the condensor unt after concrete dried up

Hi there, I'm looking to have some minor concrete work done at my house in Torrensville to make room for a new heat pump hot water system. The unit is about 640 mm wide, and I'm hoping to install it in the narrow passageway down the side of our house. The problem is there's a raised concrete strip running along the wall, which means the unit would sit quite far out into the passageway. I'm wondering whether it would be possible to either: Extend the concrete to create a level base for the unit to sit on, flush with the existing strip. Cut out a section of the existing concrete so the unit can sit closer to the wall. I've attached a photo so you can see what I mean. Would this be something you'd be able to help with? I'm not sure which option would be more practical, so I'd be keen to get your advice and an idea of what each might cost. Happy to send through measurements or arrange a time for you to come have a look. Thanks so much! Kiri

Looking for a licensed and insured plumber to replace and install my Hot water electric system. Currently is a Rheem Everhot 250L Dual Electric storage hot water system that has gone bust. Deciding between electric and heat pump given the STC and ESS rebates at the moment. Please provide quote with breakdown of pricing and which system you can install - looking to get this fixed asap

My Bosch heat pump dryer series 8 keeps flashing the error code of the water not draining (as shown in image). I've cleaned the filters and nothing is blocking it from getting drained from my end. I'm assuming something internal needs to be fixed.

New hot water system installation,removal of the old one. My current one is solar heat pump however I would like to get the instantaneous unit.

I have purchased a Bosch heat pump dryer with a mat but need it properly and professionally installed. When then installed the washing machine, they have also buggered the small laundry cabinet and am hoping someone can fix this also

I required an electrician to install a daiken heat pump, lower level, brick home.

I am looking for a licensed plumber to investigate and fix a leak on my hot water system at our home in Cheltenham. System Details: * Unit: iStore 270L Hot Water Heat Pump (Model: PASHW015-270LD-FL02-R290) The Issue: There is water continuously leaking from the valve drain pipe on the side of the unit down onto the paving. I need someone to diagnose the cause of the constant leak and complete the necessary repairs. If you are available to assist, please let me know your availability and your estimated call-out or repair rates.

Install water heat pump and dispose the existing one. Happy to get it supplied and installed, or installation only (I will get one form Bunnings). Please send thorough your quote. Would consider electric pumps as well.

Looking for a registered/licensed (Victoria) plumber to relocate an existing heat pump hot water system in my backyard. Needs disconnecting and reinstalling the unit at a new location approximately 8m away from the current position. No major changes required—straightforward relocation with new pipework. Needs new insulated hot and cold water pipework/securing to house/emptying, testing, purging etc ensure working and Supply and install suitable base

I am looking for an experienced appliance technician to inspect and service my 5 to 6-year-old Bosch Serie 6 heat pump dryer (Model: WTW85460AU). The unit has experienced a noticeable drop in drying performance over the last few weeks; clothes consistently come out damp and retain a musty smell at the end of cycles. ​I have already cleaned the primary door lint filter, wiped down the internal stainless steel moisture sensor strips, and cleared the lower compartment base. However, even on timed or quick cycles, the internal program timing fluctuates extensively and fails to properly extract moisture, pointing to potential deep-seated lint buildup inside the self-cleaning condenser fins or heat exchanger assembly that requires professional servicing. Please let me know your availability and quote for an on-site inspection and repair in Riverton, WA.

Hi I need a plumber to disconnect the LPG gas and replace with a heat pump Thanks

New heat pump dryer. Already in place. I just am incapable of reading instructions and being handy with tools. Afraid to break it. It works for 5 mins and then stops, but i have not set up properly

Install a Samsung 9kg Heat Pump Smart Dryer and remove old one,

I need to install New Stiebel Eltron 302L Hot Water Heat Pump System

Description: I need assistance removing a heat pump dryer from a custom laundry cabinet, connecting the drain hose at the rear, and placing the dryer back onto the shelf. Job details: Heat pump dryer is already installed on a shelf above the washing machine. The dryer is not screwed or fixed to the cabinet. The drain outlet is on the rear of the dryer, so it needs to be lifted out to access it. Connect the supplied drain hose to the rear outlet. Reinstall the dryer onto the shelf and ensure it is level and operating correctly. No electrical or plumbing modifications required—just connect the drain hose. Requirements: -> This is a two-person lift, so either: bring a second person, or be comfortable working with me to safely lift the dryer. -> Experience moving or installing washing machines/dryers is preferred. -> Please bring any basic tools that may be helpful (although none are expected to be required). Additional Information: Heat pump dryer weighs approximately 50 kg. Dryer is not fixed to the cabinet and simply needs to be lifted off the shelf, drain hose connected at the rear, then placed back. I'll be available to assist with lifting if needed. Location: Hamlyn Terrace - 2259 Estimated time: 30–60 minutes. Please review the attached photo before making an offer. The dryer sits on a shelf above the washing machine and will need to be safely lifted out and reinstalled after connecting the drain hose.

Hi, our 7kg heat pump dryer has started to beep indicating the water tray is full even though it’s empty. Have tried to restart it.

Emerald Heat Pump. Not filling beyond 20%. Leaking ptr valve maybe.

Washing Machine & Heat Pump Dryer Installation Hi, I need a handyman/appliance installer to complete the setup of a Bosch washing machine and heat pump dryer in my apartment laundry. Tasks: • Connect Bosch washing machine to existing water supply • Connect washing machine drain hose to sink waste pipe • Install suitable drainage connection/spigot into existing sink waste pipe (pictured) • Secure drain hose with appropriate clamp/fittings • Test washing machine for leaks and correct drainage Dryer: • Connect the heat pump dryer’s continuous drain hose so water drains automatically • The dryer water collection tank is difficult/impossible to access due to the tight cabinet space, so I would like the dryer set up for direct drainage instead • Test dryer drainage setup to ensure it works correctly Please bring any tools and any small fittings/clamps required for installation. Please review the attached photo and confirm if any additional parts are required before attending. Looking for someone experienced with appliance installation, washing machines, dryers, or basic plumbing. Location: Rushcutters Bay Flexible on timing.