Find a local Tasker to help you make a kitchen cabinet near you

Align and re-glue four kitchen cabinet doors

I am looking for a small kitchen cabinet and benchtop for a granny flat. Need most affordable price due to budget issue. Size: ideally Length 180 length, 60 width, 90cm high (can be adjusted) Requirement: Benchtop needs a cutout for an induction cooktop. Ideally 3 drawer chest , 2 door uplight cabinet. Used cabinet or bench top would be fine also if it’s in good condition.

Remove existing upper cabinet and fix other side, relocate stove and cabinets including Benchtop left hand side where fridge is there, move fridge and cabinets to stove location.

I’m looking for an experienced cabinet installer/carpenter to install a full set of base (lower) kitchen cabinets in my home. The space has been renovated: walls are patched/drywalled, plumbing rough-in is complete for the sink, and the subfloor is exposed timber. 600mm drawer 600mm drawer 600mm sink drawer 600mm dishwasher (The 2400mm bench top goes along this). Need to add support brackets to support bench top along here. The drawer panels need to be swapped out as well as one of them is gloss white instead of antique white.

I need to add some cabinets to my kitchen and also change the colors of the ones I have now. Can you help?

The corner kitchen cabinet door has dropped and bottom mounting plate poped off leaving holes. The top mounting plate sctews threads are slightly stripped. I have purchased 2 varieties of new hinges already

Install kitchen cabinets from flatpack.

I have the white panels that go above the kitchen cabinets but i need someone to install them. One section is about 3.3 and another section is about 2.6 metres.

Fix door hinges of kitchen cabinet

I have a two‑piece corner cupboard door with a hinged connector between the panels. The connector hinge is now working, but the main door still won’t sit straight when closing. A new hinge was purchased and we attempted installation, but it did not solve the issue. I need someone experienced with kitchen cabinetry to diagnose the problem and adjust or re‑mount the hinges so the door closes properly.

I have a corner door in kitchen cabinet that have hinges broken off. I have tried fixing but it’s quite old and the previous drill holes and plugs that have been removed are badly damaged. Previous drill holes on the cabinet and doors will need to be done again somehow as I’ve done a shiet job attempting myself. I have already bought what I think it’s the right hinge, a 165 degree one and the other one. Both doors approx 720mm by 350mm.

I have 3 built in Miele fridges that are built into the cabinetry. The builder did not add adequate venting into the cabinetry so the fridge can’t hold its temperature. I need someone to cut the cabinetry as indicated by Miele and place vent covers where you can see it so it looks neat. There are some round holes cut but this isn’t enough.

Need extra space to fit in a larger space in kitchen. Fridge is taller and wider than the current space

I have an above-fridge laminate cabinet, not fixed to the wall, that needs 80 mm removed from the height so the fridge fits underneath. I want it shortened from the top, including re-edging and door adjustment.

Hi, I am looking for someone with the right tools (specifically a powerful hole saw) to drill a clean hole through the internal panel between two kitchen cabinets. The purpose is to feed a cable from a microwave drawer through to the under-sink area. Access is straightforward, but the cabinetry is quite solid so I need someone experienced who can ensure a neat finish without damaging the surrounding panels. Please bring your own tools and be confident working with kitchen cabinetry. Happy to provide photos and measurements if needed. Thanks!

Build 2x kitchen cabinet from flat pack. Hang in kitchen using own screws as overhead cupboards. Please ask if you need more photos or information! Flexible with timing. Needs to be done this week.

Cabinet needs to be cut a few inches from bottom & shelf moved up to accommodate new fridge. Cabinet already removed.

Hi there, I’m looking for an experienced handyman or cabinetmaker to remove a single kitchen cabinet carcass so I can install a dishwasher. The doors and shelves are already removed. I just need the carcass taken out cleanly, including detaching it from the benchtop, adjacent cabinets and neatly cutting the kickboard. Installation of the dishwasher is not required. Prefer someone who has done this before and can ensure the surrounding cabinetry and benchtop aren’t damaged. Located in Mitchelton.

The bottom cabinets only I have kitchen cabinets that are 20mm out and need to be straightened asap for new bench top Don’t care about damage to backing as I am renovating Open to offers Need kick boards installed

I need Ikea (already assembled, without doors) cabinets installed in my laundry room. There are 2 wall cabinets, 1 tall cabinet and 4 base cabinets. There will need to a hole cut into the base of the tall cabinet for a pipe. There are 4 filler pieces. I have the detailed drawings. These will have a stone benchtop and so I will also need sturdy, large L brackets installed onto the wall in specific locations. Previous Ikea installation experience required please.