Find experienced local carpenters in QLD

Need to replace around 3m of rotten facia and lift sagging soffit.

I need to attach a made to measure timber panel over a cavity/ plumbing cabinet in a bathroom- the inner frame that the panel needs to attach to needs a small repair. I already have the panel - I just need it installed; it was meant to be done as part of renovation but was overlooked

I need to build two sets of stairs for a tiny house. Lots of other work available after first hour is complete.

Wooden outdoor table top needs sanding and resealing to restore

Custom Built-In Shelving Wall Width: 3.0 m Built-In Height: 2.2 m (aligned with door/window head height) Depth: 32–35 cm Finish: Painted to wall colour (flat panel) + timber accent features Design Intent    •   hold vertically stacked books    •   include 10 total shelves    •   provide 2 tall (70 cm) shelves    •   provide 8 standard (30 cm) shelves    •   include 2 × 70 cm high cabinets    •   blend into the room by matching wall colour    •   skirting boards to seamless blend room and cabinet    •   MDF (water resistant)with 2-pack painted finish    •   timber accenting that matches house    •   flat panel doors    •   soft-close hardware    •   full install and clean up

Cabinetry work including: (I) move existing cabinet doors to a new spot (II) remove shelving above fridge to make room for a taller fridge (III) install under bench bin in kitchen.

I need 9 m of skirting board replaced. Old skirting board removed and I will supply the new one to be installed. No painting needed. Also need one small piece of rotten decking removed and replaced- I will supply. . Also one door handle replaced - using one already at the house. Need the job done Dec 4th or 5th please

We had our kitchen installed yesterday (carcus) only and then realized we need a couple of small changes - need to move out pantry cabinet across by 18 mm to allow for a 18 mm filler panel to go next to the dishwasher to support the stone. Also need a couple of filler panels cut and added in either side of stove space - happy to pay per hour - $300 for the first 2 hrs and then hourly rate after if that is acceptable. cabinet cutting experiance and tools and install kitchen experiance

I need a woodworker with good table saw skills to pick up a dozen 2.4m lengths of pine from my place to be cut length ways down the centre with a 45 degree angle for a French cleat project. The work can be done at my place if you prefer.

I have 1 wall mounted METOD cabinet I need installing. I have assembled the carcass so it just needs hanging and the end panels installing

Cabinet needs to be cut a few inches from bottom & shelf moved up to accommodate new fridge. Cabinet already removed.

I had new carpets put in. 3 interior doors had to be taken down because the new carpet is higher than the old carpet and there is not enough space under the doors. I need a chippy or handyman to take a little bit off the bottom of the doors to make them the right length, and put them back on the doorframe.

Hi there, I’m looking for an experienced handyman or cabinetmaker to remove a single kitchen cabinet carcass so I can install a dishwasher. The doors and shelves are already removed. I just need the carcass taken out cleanly, including detaching it from the benchtop, adjacent cabinets and neatly cutting the kickboard. Installation of the dishwasher is not required. Prefer someone who has done this before and can ensure the surrounding cabinetry and benchtop aren’t damaged. Located in Mitchelton.

Looking for a good tradesman who can think for himself to sort this situation. We need to install 2 x 450mm Euro Cargo bins in the cabinets shown below. But the cabinets are not deep enough for them. The idea is to cut through the back of the cabinet and into the other cabinet behind it. Then install the bins and install a false back on the 2 door cabinet behind. The works have to be done with the cabinets in position. Cannot be removed. I'm providing the bins, but you'll need to provide the white melamine for the false back (Bunnings melamine is fine) and all the screws / consumables.

We require a handyman with builder skills to assist us to fix 2x outdoor settings as per image onto decking for a commercial sales office in DEEBING Heights close to Ipswich. Airtasker to come to site review requirements then attend Bunnings for best fixings. We will pay for fixings as required over and above Airtasker fee

Fit out existing under vanity , with mdf , doors and shelves supplied. Just need tools

Sand, stain - Need a semi-pro who knows what they’re doing here! Will need someone who has the gear / equipment required. Need to work around weather. I’ll reimburse you for all materials with receipt.

Hi, I already have the timber benchtops and just need a carpenter/cabinet maker for installation. Scope: Cut to size Sink cut-out Cooktop cut-out Join two benchtops Fix/secure to cabinets I’ll handle sealing/finishing No removal or disposal needed Cabinets are already installed and level, and access is easy. Can you please let me know your labour price and earliest availability? Job is in Nambour. Thanks!

I need someone handy with cabinetry to modify my existing kitchen cabinet so a standard-size dishwasher can be installed. The cabinet space is currently closed, so it’ll involve removing the door and part of the cabinet to create the opening. What’s needed: Alter and remove part of the cabinet and door to create a dishwasher space Ensure the opening is neat and ready for installation Tidy finish — no rough edges You’ll need: Own tools Experience with kitchen cabinetry or similar work Details: Standard 600mm dishwasher Cabinet material: laminate Location: Enoggera Parking available:yes

Build shelves x2 Only make an offer if you really know what your doing please