Find experienced local fencing contractors in Mount Waverley

Straighten up the leaning section and secure the posts so they are plumb and sturdy.

I've attached two photos below. The first shows the current state of the front yard, which has some existing vegetation but no fence at all. The second photo shows what I'd ideally like it to look like finished. Basically, it's made up of a few brick pillars, with sections between them featuring a brick base at the bottom and a metal fence on top. Because of this, I need someone to help with a few things: 1. Remove the existing vegetation. 2. Build the double-brick fence sections. 3. Install the metal fencing in the middle sections. 4. Put up a gate. 5. Install the letterbox. 6. Apply rendering to the exterior finish at the end.

The door handle on the front gate of my house has broken off. I need help to repair/ replace this. A replacement handle will need to be sourced.

Old brick fence: demolition of the previous brick wall and removal including skip bin and potentially remove all footings New and concrete block fence: including all materials such as large size H bresser block, sand cement, liquid lime, rio bars, core filling and potentially need scaffolding as well as it 2 meters high on the high end. The street end is 1.4m high. Total length is approx 7-8m. Please quote separate price for demolition and rebuild if possible. Pls note the photo with the block fence is for illustration purpose only.

Need to repair Picket Fences, which got damaged by a motorbike collision

require 16m backyard boundary fence in colorbond. Require a quote. Location is in Mt Waverley. Marlene

Open area at side of property to be closed off with a gate or two gates adjoining into space side of house 1840mm wide opening. 2000mm high approx

I have two garden gates that are currently wooden and damaged, and I need them removed and replaced with new Colorbond garden gates. The approximate dimensions are 194 cm high by 86 cm wide. Because I am not a professional, there might be about a 5% margin of error in my measurements, so I would need you to come out to do a precise measurement after accepting the job before proceeding with the installation. Could you please provide a total quote covering both gates, including materials and labor? I am hoping to get this installed as soon as possible.

Hi, I need to install an aluminum fence between the garage and the house. The total length is 4M including a small gate.

I’m looking for someone experienced in timber fence repairs to straighten and secure a leaning fence at a property in Mt Waverley. The fence part needs to be straightened is approximately 10 metres long and would require only 2 new posts. It does not need to be fully replaced. The main job is to straighten it and reinforce or secure it so it is stable and looks presentable. The job must be completed tomorrow, Friday 31 July, or Saturday morning 1 August. Must bring all tools and equipment required to complete the job. Photos are attached.

Fence and gate between house and garage is worn out. New paling fence to 1500 mm with gate and latch. Take rubbish to tip.

There is an existing fence 1.6m. Before building start we have been requested by the builder to increase the fence height to 1.8m using extension. Approximate length of the fence 27m.

Colorbond Fence Posts : 2,7m Sheet: 1,8m Sleeper Timber : 200x50 x2 each /panel Remove old fence Total 8 metres

Installing 2 new timber support posts/braces to strengthen the fence. * Securing and reinforcing the bottom of the fence so it no longer moves or wobbles.

Need colorbond fencing put in along boundary, approx 39m total at 2m height. The back 4.5m section to have timber retaining walls to bring total height to 2.4m. Hoping to get some quotes. Thanks

I have an old timber paling side fence that is starting to lean and fall in sections. Before considering full replacement, I’d like to first try strengthening and repairing it to make it stable and straight again. Access is tight on my side (plants/garden bed). Neighbour access may be difficult. • Plan is to use the solid brick house wall as a push point with bottle jacks or similar. • Several posts are rotten at the base — need new posts or stirrups concreted in. • Add a couple of extra support posts in the middle for strength.

New side gate 1, approx 730mm, would like some light frame with prestained marbau or something similar with sliding bolt to lock New side gate 2, approx 1130. Again would like something similar to gate 1. Neighbour’s driveway gate, needs to be attached to new fence but old fence was falling over, will need realignment.

14 meters of colourbond fence was recently installed over concrete sleepers. I need some one to remove the panels tie down properly with new screws or bolts and fix them back.

**postpone!!! Sorry need to postpone this task as I have made a mistake with the measurements. Will update the correct task once I hear back from my builder. Sorry for the inconveniences. Hi, i am Looking for someone to remove approx 5m of the timber fence below.

A section of my fence has shifted and created a gap. I need a simple and cost-effective solution to: - Fully close the gap - Ensure the boundary is secure (no access through) - Make it reasonably stable This is a temporary solution only (no full replacement required). Looking for a practical and efficient fix.