Find a fence installation professional in Inner South Melbourne

Due to recent installation of a new fence, I’ve had to get one panel of electric gate and its motor/panel removed. I now need to get that panel reinstalled along with its motor. The panel has been installed but I’m not happy with it as it’s a little loose. The job will also involve centering both panels and making sure gate works fine and the motor is installed safely

I need a 3.9M wide double swing gate installed (similar to the picture). Onto brick posts. Needs to be around 1.9m tall in middle section.

Money is for making phone contact , no actual work required. Looking for subcontractor who can install motor, dig tranch to take 24 low voltage wires to power point to the house. Few jobs every month. We fabricate sliding gates , swing gates etc based in oakleigh melbourne.

Remove old existing fence and replace with same timber fence 21m long x 2m high

need a quote to install a **40 metre timber paling fence** for left boundary of the lot: - Height: 1.8m - Straight line - No decorative features - Ground: level - No complex site obstacles -removal of the existing fence -requiring you are fully insured

Due to movement of our fence over time, our outdoor side gate bolt lock no longer aligns (see photos). We need a handyman to figure out how to realign the bolt lock, or reinstall a new one (which we’ve already bought).

Timber side gate to be replaced. New one to be purchased from bunnings. Product image of the one to be replaced. May need side post replacement

need to replace old fence as shown in photos below

Hi Looking for a great air tasker to install some trellis wire along a fence. The frame is done and now just need the wire Needs to be the proper wire that matches the picture Job needs 4 x long pieces - about 5m each 3 x shorter pieces - about 3m each Job needs to have the proper adjustable tensioners on one end - like the picture I have a second job also to screw in a hole into another pole - you will need a proper tap and die set for that. Easy job. Ready to go Please send me a picture of the material you will use so I can see if it matches exisiting that we already have. Thanks.

We have a small snippet of our side fence that needs replacing. We’d like a black colourbond one Measurements are approx 6mtrs & 1.8 mtrs high.

Side fence, 2 posts are rotten at the bottom, need to add / replace 2 timber post. Please note the current post was done only 5 years ago, may also need onsite inspections to check the reason why they are getting rotten so quick

Hi :) I’m looking to build 2 security gates around the side / back of my property.

Our external timber gate is not latching correctly. The self-closing / self-latching mechanism no longer aligns properly, meaning the gate does not reliably close or lock when shut. Based on inspection: • The spring-loaded latch / closing mechanism appears worn, misaligned, or partially broken • The gate no longer extends and retracts smoothly when closing • The striker and latch are not engaging correctly • Gate itself is timber and structurally sound, but hardware likely needs realignment or replacement We need the gate to: • Open smoothly • Self-close properly • Latch securely every time Scope of work likely includes (happy to take advice): • Assess existing latch and closing mechanism • Realign hardware OR supply and install a new suitable latch/closer • Adjust gate alignment if required • Ensure gate closes and locks consistently

Replace existing boundary fence. 3 meters in length approx. See pics

Fence: Timber fence approx. 36m long x 1.8m high Scope: Minimal repair only (no painting) What I need done: Re-fasten/secure any loose palings and rails Tighten/replace fixings where needed (screws/nails) Replace 3–6 timber palings/planks (max 6) that are damaged Make the fence solid and tidy, ready for painting later Clean up and remove any small debris off-site What’s NOT included: No post replacement / no re-levelling the whole fence No full fence rebuild No painting Budget guide (please quote accordingly): If you supply materials: Budget $400–$800 (include materials + pickup) Materials: You supply materials: You supply palings, fasteners, and any small consumables What to include in your offer:: Estimated time required Any assumptions (e.g., “up to 6 palings included”) Confirmation you have the tools to cut/fit palings and securely fix rails Timing: Flexible — ideally within the next 1–2 weeks.

Need to build a small 2 metre high fence and 2 x gates on steel frames to hide bins. Posts have already been put in so no need to do that. We would like to clad the bin bay in 2m high Lunawood battens to match existing fence in the vicinity. All surfaces will also need to be painted using two coats. Materials required to be quoted and paid for separately.

Straighten and support existing timber fence. Including making timber privacy panel above fence. Materials required - none supplied.

I have a low brick fence that I want to add merbau too, to match the exisiting fence on the righthand side. The hedges have been removed. See images attached.

Installation of wooden street library. Requirement of post securely into the ground

Replace damaged wooden post Can supply materials Mordialloc Area