Find local downlights installers in QLD

Licensed electrician needed in Marsden (house). All fittings are already purchased, so this is install labour only (plus any sundries). 1. Downlights: replace the old light fittings with 6 x CLICK CCT LED downlights (4 x 90mm and 2 x 72mm cut-outs). 2. Switches and power points: change approx. 8-10 single switches and power points to doubles. 3. Bathroom: remove the existing light and install a CLICK 3-in-1 bathroom heater / exhaust fan / LED light (model CK4U, 4 x 275W heat lamps). Needs the ceiling cut-out, fan venting, the correct switch for the unit and any circuit work the heater needs. Must be a licensed electrician and provide a certificate of testing / compliance on completion. Please quote a total fixed price including GST. Photos available on request.

Hi, I have the following job: 10-12 downlights outside 2 lights inside 4 chandeliers inside (2x 50 cm and 2x80cm) 2 lawn flood lights 1 ceiling fan transfer from dining to patio Some light switch changes. Let me know when you can come for a look and quote? I will provide the lights. Thanks.

Replac 6 Existing indoor hardwired old mode Downlights to plug-in mode LED Downlights. Need a licensed electrician to conduct the job and tax invoice/certificate is required upon completion. All new downlights will stay in its original position with current electrical wires, from my point of view no extra work is needed except changing from the current hardwired mode to plug-in mode and then install the new led lights properly. I will provide downlights (Arlec 9W 92mm Tri-Colour Dimmable LED Downlight Recessed Lens) x6 and plug bases (DETA 10 Amp Single Outlet Trade Plug Base) x6. Please test those lights and ensure they are operating correctly and leave the ceiling neat after installation. Thanks

3 pendants Need wire up to switch Are hung gtg

I need to get 8 led downlights and Hotplat gas connected by electrician

Replace 2 Existing Downlights with Integrated LED Downlights I need a licensed electrician to replace 2 existing 12W DET592 downlights in my bathroom with new integrated LED downlights. Job includes: • Remove the 2 existing downlight fittings. • Supply and install 2 new integrated LED downlights suitable for bathroom use. • Prefer white fittings, approximately the same size as the existing lights. • Lights should be IP44-rated or higher and suitable for bathroom installation. • Connect to the existing electrical wiring/driver as appropriate, or replace/remove the existing driver if required for the new integrated fittings. • Test both lights and ensure they are operating correctly. • Make good/leave the ceiling neat after installation. Important: Please include the cost of the lights/fittings and installation in your quote, and advise which model you intend to install. Licensed electrician only, please.

6 downlights,# 6, 3pin plugs, 1 double power point, speaker wire and 2 ceiling speakers supplied. What's not supplied is the electricity cable. Installation is in the double garageband has a manhole. Existing 2 gang tubelight switch to be used for this 6 downlights.

Install Clipsal 1300mm DC Ceiling fan, and four SAL Wave LED Downlights, in place of existing light fitting. DC fan and downlights will only be supplied. Replacement of the existing single switch, and associated wiring & accessories is by installer. its a single story with roof access.

I need 11 light switches (6 Single/2 Doubles/2 Triples in bathrooms and 1 4) changed. I have purchased all the complete switches, just need them changed over. I also need a 90m downlight replaced, ideally SAL Wave. I dont have this so would need it provided

Job Overview I need the colour-temperature selector switch adjusted on approximately 43 existing LED downlights in a two-storey home. IMPORTANT: The ground-floor ceilings are approximately 3 metres high — considerably higher than a standard residential ceiling. You will need to bring suitable ladder/access equipment for this height. The lights are already installed and fully operational. No replacement fittings or new lights are required. Scope of Work Approximately 25 downlights downstairs 18 downlights upstairs in total, including the 2 located over the staircase Change each downlight from cool white to warm white using the existing selector switch on the fitting Carefully lower each fitting enough to access the switch Change the setting and reinstall the fitting securely and flush with the ceiling Take care not to damage ceilings, paintwork, retaining clips, wiring or fittings Ceiling Height & Stair Access Ground-floor ceiling height is approximately 3 metres, NOT a standard 2.4–2.7m residential ceiling. There are also 2 downlights positioned over the staircase, which will require appropriate equipment and safe access. Please only offer if you have the appropriate ladder/access equipment for the 3m ceilings and the two staircase lights. Please quote for completing the entire job and confirm your availability.

Need a licensed to electrician to replace a circular fluorescent fitting with a downlighting

Looking for a licensed electrician to replace the existing ceiling lights throughout my townhouse with modern recessed LED downlights and add additional downlights where required. Approximately 25–28 downlights in total across: 3 bedrooms / office: approx. 4 downlights per room, positioned around the existing ceiling fans Living room: approx. 4 downlights around existing ceiling fan Dining area: approx. 4 downlights Kitchen: approx. 4 downlights Upstairs hallway/landing: approx. 3 downlights Small downstairs toilet: 1 downlight Existing renovated bathrooms do not need any work There is roof-space access upstairs and some ceiling access panels downstairs, although downstairs access/wiring will need to be assessed. Please mention whether your quote includes patching any holes left by the existing oyster lights. I'm happy to arrange plastering/painting separately if that's normally excluded. Happy for electrician to supply and install, but please specify the brand/model of downlight included in your quote. Please quote for the complete job.

Hello, We are looking for a licensed QLD Electrician to attend our retail store, on Albert St (Brisbane CBD), to replace three faulty ceiling downlights. The Issue: Three recessed LED downlights on our main sales floor have failed (flickered and went out completely). This is affecting the lighting on our sales floor, making some display areas dim. The Job: The task is to replace the three faulty LED downlights. The scope of work includes: 1. Safely accessing the light fittings in the high ceiling (a suitable ladder is required - Approximate ceiling height: 3 meters). 2. Removing the three faulty downlight units. 3. Supplying and installing three (3) new, suitable replacement recessed LED downlights and drivers. 4. Ensuring the new lights' colour temperature (warm white) and brightness match the existing lights in the store. 5. Testing the new lights to confirm they are secure and fully operational. Please note: The successful contractor MUST supply the three new compatible replacement downlight fittings and drivers. The cost for this hardware must be included in your final offer. Requirements: - MUST be a fully licensed and insured QLD Electrician. - You must have your own tools, including an A-frame ladder appropriate for a high commercial ceiling. - Experience with commercial lighting systems. Location & Timing: Location: 136 Queen St, Brisbane City QLD 4000 When: The job can be completed at your earliest convenience. Please state your availability in your offer. Please provide a comprehensive quote for the complete supply and install. Thank you.

We have 7 wired in down lights that need replacing by an electrician.

We have quite a few light globes out + 2-3 down lights. Just needed new globes put in and wipe over the tracks please. We can supply globes after seeing which ones we need as I don’t think we have enough

Following electrical work: - Replace 6 downlights which I have purchased. - Change over a ceiling fan - Replace office light fitting.

Hi, I’m looking for a licensed electrician to do a small lighting job in a kids bedroom. It’s a single-storey standalone house in Mermaid Waters, with access through the ceiling/roof space as required. Scope: 1. Cut 4 x 90mm ceiling holes 2. Wire and install sockets/downlight points for 4 Philips Hue downlights 3. Remove existing ceiling fan 4. Install a LIFX SuperColour Ceiling Light Model: 38cm White Trim I already have the lights. Need someone who can supply any required electrical fittings, cable, sockets, connectors, etc, unless you prefer I buy them first. Because this is a kids bedroom, I need the room properly protected before work starts — bedding, flooring, etc — and fully cleaned up afterwards, including dust and debris from cutting the ceiling holes. Must be properly licensed and able to complete the job safely and neatly. Flexible with timing. Thanks!

Replace 3 lights. Will need to buy 3 down lights. The 3 fancy light are the ones I want to get rid of for something similar in the other photos.

Need two of the down lights changed. One in wardrobe and other in living room.

Quotes for Electrician to convert existing batten lights to LED downlights throughout house approximately 15 lights in total needing done.