Find experienced local carpenters in West End

There is a splat of Prosecco on the roof. It is a small area but I need to fixed before moving out this rental. Perhaps 0.5x0.5m affected in total. Unfortunately I don't know the exact colour of white on the roof used to paint over

Floating floor troubleshooting on last row plus quarter round installed Bottom of door catching Shelves installed in plaster wall I’ve got some photos but can send more. 1) Floating floor (uniclic). Have installed most of this but the cuts in the last row aren’t working - only have a jigsaw. Also need quarter round installed throughout perimeter and mitred at the corners and a threshold at door. It’s a sunroom 4.7x2m. 2) The door is catching on the new floor and I think now needs a few mm planed off bottom (don’t know if this can be done without removing). 3) Bought a hanging shelf that the shop recommended I get properly hung in our plaster walls with stud finder, etc. it’s like this: https://themodern.com.au/products/plank-shelf-system-tasmanian-oak-1

I have 2 stainless steel hollow rods. I need them drilled and threaded. Our drill is not powerful enough. It should literally take 15 minutes with the right tool.

Waterfall kitchen island approx 1m wide, 1m high, 3m long Sink in the middle Stone is blemished in places - normal cleaning does not do the job suspect needs to be ground / sanded and recoated? or just polished (I am not an expert) Inspection required before final quote can be accepted

Hi — I’m restoring a 1960s Queensland blackbean sideboard and need a small piece of solid blackbean milled to match an existing trim profile. The job: • Mill approximately 1.8 lineal metres of solid blackbean to two thin trim strip (roughly 10–15mm thick, exact dimensions to match a reference piece I’ll provide) • The reference is an intact trim on a matching sideboard I own — I can show you this • Edge profile is slightly rounded) • I will supply the timber (reclaimed blackbean boards, 186 x 18mm) OR happy to discuss you supplying if you have stock What I need from you: • Access to a thicknesser and table saw (or equivalent) • Experience with hardwood — blackbean is dense and can tear out if rushed • Ability to match dimensions precisely to a reference piece • Installation — I’ll glue and finish it myself unless quoted • Finishing — leave it raw, I’m oiling it to match the rest of the piece

Put together ikea cabinets - 1 laundry 1 overhead Install overhead cabinet to wall Plaster 2 small holes (from removed down lights)

6 pieces of wood and a hinge. Will pay for quality https://learn.kregtool.com/plans/bailey-chair-for-dogs/

I need a skilled builder or handyman to help me build some shelves. I have some drawings, rough plans and measurements, I just need someone that can do a better job than me. I will supply materials (ply).

Overhead cabinet resizing, cabinet is already out and needs cutting down

Hi, I want some timber attached to the top of these legs to create a hallway table. Hoping for it to be over 200cm in length. Very basic. Hope to have job completed by middle of April Thank you so much

I need a new set of external wooden stairs painted/sealed. Would involve filling screw holes, light sanding and cleaning and then primer/painting/sealing. Looking for someone with experience who could come and quote for the job and then get the job done. Have put $10 on job only because need to receive a quote first and get an idea of cost.

Problem with Door in old qld workers’ cottage from bedroom leading out to verandah. Has warped at the top and won’t open. Looks like a bit of wood was added to the top some time in the past and it has a small crack in it. Not sure if you can fix door or I need a new one so may need to adjust price.

Engineered stone benchtop to be removed and replaced with shorter benchtop. Remove one of the base cabinets under the benchtop to fit the new one.

Need to cut out a raised floor to fit fridge in

* Fix cupboard thats having same issues with slide door. Door slides from the top rung. Unsure the issue. But it's not sliding properly anymore. Cupboard is wood. *Replace and install broken door stopper . Its a rubber stopped.

Sand timber back to clean timber and apply 3 coats of Matt varnish. Facade is around 8 x 2.5m including the doors/windows. Location is on commercial street so sanding would need to be done out of hours ie early morning or late night Optional extras to be charged separately 1) repaint ceiling in same area 2) repaint window frames. Please indicate in your quote if you’d like to include the other items

Need to fix deep scratches in timber floorboards caused by moving a fridge. See image

Stainless kitchen bench needs welding job. Need reinforcement

There was a mark on my ceiling which must have been done with the luggage. And now after trying to erase it, it has been extended and become a grey stain. I need this to be removed today asap. Before 1 PM if possible.

I need my cabinet trimmed so my new rangehood can front circulate (see pictures) It will need to be trimmed by about 30mm.