Find experienced local carpenters in Kellyville

Looking for a cabinet maker or joiner to complete two small jobs in my kitchen. 1. Modify the overhead cupboard to suit a new 60cm Bosch slide-out rangehood. The current duct cover is in the middle and may need to be removed or modified to suit the new rangehood. Remove the duct cover basically. 2. Remove the internal shelf (middle shelf) from the another cupboard. Photos are attached.

I purchased an office desk furniture as per photo attached. I need someone to assemble the panels to convert in to a full peace of furniture

I’m looking for an experienced cabinet maker or carpenter to design and build a custom outdoor shoe cabinet. Available Wall Space: * Width: 1.2 metres * Height: 2.23 metres Requirements: * Suitable for outdoor use. * Built using waterproof and weather-resistant materials. * Strong, durable, and low maintenance. * Neat, modern finish with plenty of shoe storage.

Need a hole cut through the side panel of my laundry cabinet so the washing machine/dryer drainage hose can pass through to the waste pipe. # Cut a neat hole in the laminated cabinet panel # ring suitable hole saw/tools # Ensure a clean finish with no damage to cabinetry # Photos attached for reference Looking for a handyman, carpenter, or cabinet maker. Flexible timing. Location: KELLYVILLE

One of the hinges of the bathroom door came off. This needs to be fixed. Hinge and screw is already available

I have integrated Fridge. The outside Cabinet door is attached with the Fridge door via running track system. Fridge needs to be leveled to able to connect/ attach to the cabinet door.

Need an experienced cabinet maker or carpenter to modify the overhead cabinet above my fridge. The opening height needs to increase from 1800mm to 1870mm. The cabinet doors will need to be shortened by approximately 70mm and refitted. White gloss finish. Looking for a neat, professional finish. Photos attached.

I need my existing kitchen oven housing cabinet increased by 10cm. I have an existing 90cm x 50cm x 57 oven which is being replaced with a new one that is 90x 57 x 57 so I need the housing adjusted. There is a 20cm drawer below so this can be used (10cm) to increase the housing to fit the new oven in. Therefore need sufficient skills to increase size using this drawer space including making the remaining 10cm gap good - probably by using the existing drawer cover and cutting in half and fitting (ie no long a drawer as it isn’t used anyway).

Need to extend the Kitchen bench top cut out for a gas cooktop by up to 2cm in depth on one side only. Simple cut as the bench is wooden with a laminate top of 4cm deep. Also require hack saw off small blocks of wood on all 4 corners (see picture)

Looking for a skilled and experienced carpenter to help modify an existing built-in cupboard space. Job Scope: Remove existing timber framing/trim around a built-in cupboard Increase the vertical clearance of the space to approx. 2400mm Prepare the opening to fit an IKEA PAX wardrobe (2360mm height) Ensure the finish is neat, level, and ready for wardrobe installation. Please note there is beam like timber but its not structural beam and check with engineer can be removed by the experienced carpainter.

Empty cupboard converted to drawer s in the kitchen and cupboard doors for two cupboards

Deck needs to be restrained. Was originally done 6 years ago

I want to order new custom kitchen cabinet doors from Sydney Doors. They need correct measurements of the cabinet doors and the hinge positioning. I need an experienced person to do this for me and to complete their order form for me. The new cabinets will be in the Shaker 5000SQ0 range and painted in Green Bottle colour by British Paints in polyurethane paint and done with a pencil edge. Would prefer if this is done either early morning or evening or on a weekend. There are 22 cabinet doors to be measured and 6 drawers.

I need a carpenter who can make a wooden ramp for a dog to walk up and down, from Alfresco deck to backyard. Height is 1meter. Dog getting old and struggles to climb up stairs.

• Remove existing door. • Build 2 timber wall frames (75x35mm pine) and install at entry to left and right side bedrooms. • Install steel door frames and hang 2 doors standard height (2040H x 820W) hollow core door frame (116x38mm). • Sheet walls with plasterboard and set joints also carry out patching. • Remove existing light switch and relocate to outside of bedroom entry (right side bedroom only). • Install new skirting where required. • Install door locks. • Paint walls, doors, frames and skirting: - 1 x coat undercoat. - 2 x top coats. - Paint colours as instructed. - Already pre approved from Building Manager and Strata. Just needs license and certificate for the contractor. Attaching photo of unit similar to us which already did the renovation. Attached floorplan shows the door circled in red that needs to be removed to be used on the study room. Bed room with blue line, study room with red line

I need a carpenter or handyman to repair a rotten timber section under a dormer window on the second floor. The timber at the bottom of the window frame has signs of rot and paint peeling. It appears to be caused by weather exposure over time. Scope may include: • Removing the damaged timber section • Replacing with treated timber or suitable exterior material • Sealing and weatherproofing the area • Preparing surface for repainting The window itself is fine – the issue is the timber trim underneath. The area is accessible from the roof (tiled roof). Photos attached. Location: Sydney Flexible with timing. Please quote including labour and materials if possible.

1.Install laundry benchtop from Ikea - Needs to be cut to exact measurements 2.Install Ikea cabinets on the wall in laundry using suspension rail by Ikea anchored to the studs. Measurements 120×42×64 Link below - https://applink.ikea.com/tY8M9r9M4w--49442006--au--en 3.Install clothes hanging rod in laundry - needs to be cut to exact measurements 4.Install Ikea base cabinets underneath the benth. Measurements 120x42×74

Patching the entrance door with stain & varnish where the old lock was installed.

I have a 230 * 200 laundry room. I want to install cabinets in this room. I can buy things, or you can get your own. Please visit and give me a quote for it.

Hi, I have installed wardrobe from IKEA but there is a gap towards the end and on top which needs to be filled by white timber/wood (filler) so it looks neat. Need this job asap- thank you!