Find experienced local carpenters in Hornsby

I have a 09 hatch just want someone come round attach a stainless exhaust tip to it.3in hot dog already on an old exhaust pipe just cut flange weld .

Handyman required to cut small hole. This is a 5 minute job for someone who has the right tool. I have a Washer/Dryer that has an antiflood mechanism that is attached to the hose. This does not fit through the standard holes cut out for the hoses. The metal will need to be cut to allow the mechanism to pass through to taps. Photos attached here of current set up that will need to be replicated at new place that am moving to. This task is time critical as need to drive back to meet removalists. Preferred time is 9am. Note: Installation of Washing Machine not required. I simply need the hole cut. Thank you!

Looking for an experienced cabinet maker/joiner to build a custom recessed bathroom cabinet. Niche size: - 460mm W × 180mm D × 590mm H Requirements: - Custom cabinet to fit inside the niche - White finish - Moisture-resistant material suitable for bathroom use - Mirrored cabinet door 460mm W × 800mm H - Fixed mirrors on both sides align with the cabinet door mirror. Location: Hornsby, NSW Drawings and measurements are attached. Please provide photos of similar work if available.

Hi, you have text me about the mirror cabinet. Please contact me.

I’m looking for an experienced cabinet maker, joiner or handyman to design, build and install an economical shoe-storage cabinet in my apartment in Hornsby. I don’t have the dimensions, so the space will need to be measured. I’m open to custom-built or modified flat-pack solutions using affordable materials. Please include materials, delivery, installation and wall fixing in your offer. Photos of similar work would be appreciated.

Need a qualified handyman or carpenter to inspect and repair an upper kitchen cabinet that has a vertical gap between panel and wall.( look like cabinet pulling away from wall) .The gap stay the same size whether the cabinet is full or empty. It is the part of continuous row of upper cabinets. The wall is double brick

We are looking for an experienced carpenter, joiner, or sash window specialist to repair and restore several original timber sash windows. There are 3 double sash windows, 2 single sash windows, and 2 small windows, all on the ground floor. Stage 1 (Priority) – Make Windows Safe, Functional & Weatherproof •Replace broken sash cords and repair sash mechanisms as needed (I have identified at least 6 broken cords) •Check all windows and repair, re-fix, or replace any loose or damaged glazing beads (glass-retaining strips), mainly on the exterior side, to ensure all glass is secure, properly fixed, weatherproof, and well sealed. •Repair chipped, damaged, or deteriorated timber and fill small holes where required •Improve weatherproofing and draught sealing. Stage 2 (Optional) – Restoration & Painting •Remove old peeling or flaking paint •Prepare timber surfaces •Repaint windows in a bright colour(white) Please provide separate quotes for Stage 1 and Stage 2. We may proceed with Stage 1 first and then decide on Stage 2. Note: All windows have recently been washed, making it easier to inspect the condition of the timber, glazing, and paintwork. Photos attached for reference.

Current vanity cabinet is damaged. Only the cabinet, without the top need replacement. Dimensions: 77cm H, 89cm W, 45cm D

Hi, I am looking for someone to reduce the cabinet height so that a new fridge can fit underneath it.

Supply and install two small white PVC (or similar lightweight, water-resistant) cabinet doors to cover an open storage alcove above a wall-mounted fish tank. Approximate dimensions: 48cm x 65cm x 12mm-13mm. Include hinges and push-to-open latches or small discreet handles. I attached the image of how it should look like when finished.

Two double story houses to be done in Hornsby with material labour and everything labour of carpentry and steel beams etc.

Need handyman to widen cabinet opening for a dryer. Dryer width 600mm. Current opening 570mm, need to increase around 620–650mm clearance for a 600mm dryer. Left cabinet can be made narrower and divider adjusted. Simple cutting and adjustment. Photos attached.

Need somebody today. The main bed frame is fine. Need a 2x1in piece of wood 70-90cm long attached to the side to hold up the slats. The existing piece was a bad repair and needs to be removed and replaced. It just needs the wood piece, a drill and 6x 2-inch screws to get the job done. Maybe a saw to cut back the bad edges of the existing slat support. A claw hammer to pull the old piece off. Perhaps 4 more 2in screws to attach a center slat to the main frame to stop the sides splaying apart. Should take under 1 hour.

Retail Store - Visit during store open hours. - White timber battens have been double sided taped to cover up some old wall racks. we need these to now be screwed on permanently - Existing floor entry mat is worn. please measure the size so i can order a new one

We are looking for someone to assist in our Hornsby workshop to assemble custom timber projects. We need someone with experience working with timber and operating workshop machinery. If you can interpret plans and instructions, dress & shaping timber and assemble products to time and specification, we'd love to try you out.

I want the kitchen cabinet doors to be replaced with similar type doors. If somebody nearby Hornsby can come and have a look to give a quote, that would eb great. I am attaching some picture to give you the idea, but it may not give clear idea about the volume of work. I can buy the product but somebody needs to install it.

I need four wardrobe shelves cut to size - a few cm off the ends. Thickness of shelves 16mm. Already marked and ready to cut. I can bring to you if you’re within a half hour drive.

A wooden king size bed has had a joint ripped off from the screws. The bed is rather heavy but I can lend a hand with it. As you will see from the pictures, the screws can't go back to the original holes as the wood is splintered.

custom cabinets to store glasses sun glasses

*edited* Must be highly skilled handyman, joinery, cabinet maker all rounder. Must have own tools, insurance, licence. 1. Install IKEA besta 3 X door cabinet onto plasterboard wall below tv. 2. Fix two drawer timber centre rail/runner on Chest of drawers solid timber. Two drawers rails broke. 3. Secure benchtop to cabinet in coffee bar/kitchen. (Newly created coffee bar) 4. Install 8 X drawer knobs to chest of drawers. 5. Install door to IKEA Billy bookcase tall and secure to wall. 6. Assembly Alex wide drawers IKEA. 7. Hang 1 x art work to plaster board.