Find a professional balustrading contractor in QLD

Need the balustrades and stair handrail replaced and rebuilt.

Install about 5 metres of diecast balustrade on a concrete floor

We need someone to Build and Supply Balustrade’s for our new deck. These can be built off site and can arrange to pick them up. We want black 100x100x4mm black hog wire fencing with hardwood timber framing. I have uploaded photos for the look we are wanting. I need 5 of these made. Openings between posts are 2600 on the sides and 2700 on the front. Can supply exact measurements. Happy to pay for materials separately. Would like it done within the next 2 weeks.

Wood rot to parts of the patio balustrades, bottom rails to the front patio are installed backwards, insufficient balustrade height to the rear patio, some loose and rusty fixings to the balustrades, balustrades are nailed not screwed.

2 sections of balustrade need to be rejoined, original pieces held. Photo is of one section, other section similar

We need 12 stainless steel balustrade wires reinstated on one side to an existing deck post. Must have swager to crimp the wire. Existing wire can be repurposed but Installer will need to provide fitting hardware for the missing post side. Happy to reimburse for this hardware if you provide a receipt.

Able to fabricate single straight staircase and landing simple modern style powder coated steel white or black to replace wired ones in pic.

Unscrew and remove glass balustrade and leave only timber.

I’m looking for someone to sand my deck, including the balustrade and stairs. Dimensions of the deck are 11.5m x 3.5m (approx) - with an additional section near the stairs 1.4m x 1.8m in length (approx).

Remove rotted sections/ replace Will most likely need a chipie or apprentice I will need a quote with materials and time

Assemble and hang window hoods, hang veranda door, build small balustrade (rough pictures of possible style and where it is needed)

Supply and install wire balustrade . 6 +3 meters .

Quote Needed - Supply and Install Internal Stairs + Handrail + Balustrade in Commercial Building Must be build to commercial code and provide correct forms for certification We're on a budget: $5000-$8000 We're thinking... 1. MDF stringers 2. Polished Blackbutt Treads 3. SS Handrail/Balustrade OR Hardwood

I need a balustrade to be available to see me tomorrow or Friday to check the job at hand it. it has Timber, glass and aluminum. please let me know when you can come to see please

Cut the ends of cables (2 ends of 10 cables = 20 total cuts), replace end screws with more robust anchoring to allow for appropriate tension, such as Jaw/Swage Turnbuckle Rigging Screws with end Terminals and stainless steel eye screws. Wire is 3.2mm 7x7. Timber posts. You can see in the attached photo that two of the end screws have come out, so we've decided it makes sense to replace all the ends of the horizontal cables, as well as the ones next to the staircase.

Hi, I have a 9x5 meter covered deck which needs oiling. The main areas of attention are the balustrades and the stairs as well as the roof posts. Once that is done then I would like to proceed to doing the main deck and I would also like to avoid sanding as much as possible just to do only very very light sands and to coat with Sikkens 2-3 coats which I can supply or if you have a trade license you can get it through your account whichever way you prefer. Thanks!

Need someone to install balustrade wire, must have experience. I will supply the kit. Also have 2 gates that need to be fitted

Steel balustrade wire is loose and I cannot tighten it as I don’t have the right tools to do the job. Swaged stud fitting spinning in post without tightening/catching

Hi, I need a quote for two angled stair balustrades fabricated to match the existing deck balustrades at my place please. Quote Job details: 1. Come to site to take measurements (I have an order form with approximate sizes if helpful, but I will need you to confirm) 2. Fabricate balustrades to match the current style used on the deck 3. Powder coat in black 4. Supply only (installation optional – I can install if needed) Approximate sizes (guide only): Height: 900mm, Length: 2500mm Height: 900mm, Length: 1800mm

Replace bottom rail of both balustrades and install new slats ton half of each balustrade (may be able to get away with less). Painting will be done by others. Materials to be supplied and installed by Airtasker, including removal of removed materials.