Find a professional awning contractor in VIC

Manual awning to be put up out the back of my stufio above the roller shutter

Sonfy retractable awning not responding to remote have changed battery on remote assume it’s a motor issue please help

I need an experienced handyman or awning installer to install an outdoor awning at my restaurant. The awning has already been purchased and is on-site. I need someone with the appropriate tools and experience to securely mount it to the building. If you have previous experience installing commercial awnings, please mention it in your offer. Location: [Carlton VIC 3053] Flexible with date and time.

On a secound storey. Will need a lift - too high for a ladder. I do not have a picture of the ground. I am away. It is however facing a concrete driveway in an apartment block.

Install awning, similar to supplied pic (that one from manufacturer, Outrigger Awnings). Job requires: - Marking, levelling, drilling 24x10mm holes, install using masonry screws. Manufacturer recommends drilling 8mm holes first, then expand to 10mm. I have the masonry screws. - Install, tension, drill and rivet awning as per manufacturer's instructions. - Bring experience and advice on the above. Second pic is installation site. The wall has a downpipe, which will be accommodated by installing the batten slightly away from the wall (this has been discussed with the manufacturer). Total size of awning is 6.2m (along wall) x 2.6m. Awning is delivered and ready to be installed. I figure this is about one day for two people (builder plus 1). I can also assist.

I need an acrylic sign to be installed on the awing of a shop front and then also removed will need an extendible ladder as it is about 4 metres height

Need an awing installed at rear of property

We have a motorised awning we are wanting to install on our back deck. It was given to us by family, although the remote has been lost. Needing support for installation as well as someone who can assist with programming a new remote/ finding the right remote for it.

Looking for an experienced handyman or carpenter to install a Canopia Sophia awning (1.6m x 0.9m) over my rear door entrance. Awning materials & assembly instructions are supplied in kit. Will need to bring own tools & appropriate heavy duty timber screws, washers & weatherproof sealer. The awning will be attached to 50mm (approx) thick timber, which sits behind grey mini orb cladding. Happy for the awning brackets to be neatly pre-drilled and mounted using standard spacer sleeves/washers to keep the mini orb flat.

I need help lifting a motorized awning your job help me measure and helping installing the awning. I will provide all the tools

Our motorised folding arm awning is not retracting as it should, and we have been advised it’s likely because the motion sensor batteries need replacing. We require someone with a ladder and tools to locate the awning’s motion sensor/s and replace the batteries (3x AAA batteries, provided). Instructions included in the photos section. Would prefer someone with experience in servicing motorised awnings in case other repairs may be necessary.

I have a van with an awning but it’s too small so I bought a bigger one to install. I want to then move the smaller awning to another van i have. Both have roof racks to attach to

Metal fastening of external awnings loosened from brick wall

The awning window highlighted in yellow is what needs to be replaced to a fixed window. This is to stop the glass door getting smashed if the awning window is open and someone opens the door into it.

Hang outdoor motorised retractable awning into weatherboards (approx 50kg) Roughly 3m wide. Can do tomorrow or Saturday.

Awning is 3 meters long and 1.5 extended.

I have a Stockton Drifta 270 awning, and 2 x Skinny Jim strong boy bars on my XL Jimny. I was informed by Skinny Jim that the supplied mounting equipment from Stockton can be used with the racks.

Looking for someone experienced to cut an aluminium roller awning Need to have own tools Need today Other options Take the awning away and dispose of it (no cutting required)

I have a canvas window awning that requires installing into a brick house. The canvas is 2700mm long and comes with all the parts required to install as it was removed from another window.

We have a click n fit awning that we need to install on cement sheeting wall There is an electrical cable somewhere behind due to a drop down movie screen The awning has been put together and just needs to be installed above sliding door We have someone available to help with the lifting after 3.45pm The awning is aluminium and light though