Find a reliable appliance technician in North Sydney

Washing machine is most likely blocked due to when i wash washing a rug and it blocked the water draining out. Everything else seems to function okay, the water just won’t drain

Looking for an experienced coffee machine technician to diagnose and repair my Breville Dual Boiler at my apartment in North Sydney. Visitor Parking provided. Steam wand light turns on, but no steam comes out No 3 beeps error – machine just stays silent Issue started a few weeks after a descale Steam wand tip has been removed and cleaned; still no steam Espresso side works normally Suspected issue is with the steam boiler (water level probes / refill / thermal protection / control board) rather than the wand itself.

I purchased a Bosch Exhaust fan for above my stove but require a re-circulation kit to be installed within it (as there is no exit for the exhaust air in my apartment). The kitchen installers advised I would need to have this complete separately. Looking for an experienced technician to come install on Thursday 6th March.

Recliners not operating consistently

I have a DF64V grinder that has stopped working. The RPM does not light up and the motor does not run. I’m looking for someone that might know how to fix this. I’ve opened it up to have a look, noticed a slight burnt smell.

The remote control (HCP-S373A) is not working after I pressed the RED stop button; the electrical cord looks exposed. I don't have a replacement remote control yet but had a look at the video 'how to replace remote control' and it looks too difficult for me to do.

Title: Install custom metal trim edge around cooktop – North Sydney Hi — I’m in North Sydney (2060) and need a small custom job done with quick turnaround. I have a Bosch ceramic cooktop already installed and want a custom metal trim edge fabricated and installed around the exposed glass edge. This is a small, detail-focused job — not a full kitchen project. What I’m after: • Clean, minimal finish (similar to factory framed cooktop) • Material: brushed stainless steel or black anodised aluminium • Thickness: approx 1–1.5 mm • Profile: L-shaped trim  – Horizontal leg ~8–10 mm (on stone)  – Vertical lip ~3–5 mm (visible edge) Important installation requirements: • MUST NOT touch or clamp the glass • Allow ~1–2 mm expansion gap • Fixed to the stone only (heat-resistant adhesive) Photos attached. Happy to take your advice if you’ve done similar work before. Timing: Looking to get this done by end of next week if possible — happy to pay for a quick turnaround. Please include: • Relevant experience/photos of similar work • Your approach to fabrication + install • Availability Thanks, James

Dryer keeps cutting out and doesn’t work

I need help to fix the scratches on our Samsung Fridge. We got these scratches from our daughter’s bicycle. Happy to hear offers. I can send some more pictures if needed. The fridge is new and the only are affected is in the pictures. -Anuj

My dryer has stopped working. There was a slight burning smell before it stopped working.

Victa 2 stroke mower running recently difficult to start. Need on site service

I need a dishwasher picked up from North Sydney and transported to Woolloomooloo, installed in Woolloomooloo, and the old dishwasher removed from Woolloomooloo please!

Repair fridge working but started making noises.

Relocate smoke alarm about 2 meters away

Meile dishwasher showing F 24 error

Washing machine is installed. There may be a leak at the back due to the tubes not tightened. Needs someone to move the washing machine out and tighten the tube. I have the tools and parts

Washing Machine Leak – Diagnosis & Repair Needed Hi, My washing machine is leaking water and I need an experienced technician to diagnose the cause of the leak and carry out repairs if possible. Details: • Washing machine is leaking during use • Unsure where the leak is coming from • Need help identifying the issue (hose, seal, pump, etc.) • Repair on the spot if parts/tools allow (or advise next steps) Requirements: • Experience with washing machine repairs • Own tools • Ability to clearly explain the issue and solution Please let me know your experience and availability. Thank you

GHD hair straightener - 2 or 3 years old not heating and making a beeping noise

Not all zones are working I turned programmer off and now it has gone wrong

Dryer stopped working sounds electrical