Find experienced local tradies near you

I had a boiler removed and the internal wall needs rendering and plastering. I also have a fireplace that needs blocking up and plastering.

Need someone to put an awning up on back of house as sun protection

electric gibus awning / line not moving. need to programme a new Somfy Smoove and make sure everything connected to power it so it can move in and out again. This job is to site visit, to supply and programme a new somfy smoove. Any further work to be agreed and charged on top

We are a sauna operator in North London. One of our sauna doors has a timber frame with large glass panel. We are struggling to get it closed and sealing in the heat. We would like someone (a door specialist) to come in and assess and adjust the door - thank you

Site visit to review our electric awning

My rocker pillar under passenger door is rusted and I need like 12 cm maybe 14 of welding

Need a qualified electrician to hardwire a new Insignia MXOS1700 hybrid sauna inside my home. This is a hardwire-only unit - it has no plug and must be permanently wired to a dedicated circuit from the consumer unit. It's an outdoor-rated model being installed indoors so no external cable runs needed. Electrical Specs (from manufacturer manual): Harvia 4kW stove - 240V single phase 4 x far infrared heaters - 1,320W total (240V single phase) LED lighting, Bluetooth, control panel - 120W (240V single phase) Total load: 5,792W / 24.2 amps 240V single phase only - no three-phase or supply upgrade needed Requires dedicated 32A MCB and 6mm² T&E cable minimum (depending on run length) Scope of Work: Survey cable route from consumer unit to sauna location inside the property Install dedicated 32A MCB in consumer unit (spare way needed - can send photos of fuse board in advance) Run Twin & Earth cable from consumer unit to sauna Install local isolation switch near sauna Make final hardwire connection at sauna's electrical junction box Test, certify, and issue Electrical Installation Certificate (Part P compliant, BS 7671 18th Edition) I have the full Insignia installation manual and Harvia wiring diagram available on the day. Timing: Must arrive by 12pm Friday. Estimated job duration 1.5-3 hours. Note on cable run: The sauna is on the first floor, directly above the consumer unit on the ground floor. They share the same wall, so the cable run should be very short and straightforward - essentially straight up one level.

The damage to the render sustained during a FTTP installation needs repairing.

awning in read garden to be attached to rear of the house. Will be a 2 person job and ladder needed

I have had some issues with damp at my property due to issues with an external render.  I am looking to render one external wall (ground floor) at my property to avoid moisture coming inside.  There are cracks in the render and it measured high in moisture in many places. There was previously a lean to shed which has now been removed.  Instructions are: remove the render back to the brickwork. Treat the bricks with three coats of Cementone Aquapruf then render the wall with a moisture inhibitor in the moisture mix. Ensure that the new render ends above ground level in a bell mouth drip. 

I have a wall that needs to be rendered (sand and cement) . It is a concrete wall that was built during last summer. Only 1 side needs rendering. Tasker needs to provide all materials. Apply mesh and 2 coats of render. I will paint myself. It's 16m by 1m. Easy access to the rear and side of garden. Parking on my drive is available plus permits if needs be.

Remove 3 built in cuboards. the sides are made from drywall and we need them taken out before we can lay down new carpet.

Treat a 5m x 3m decked area, the steps, balustrades & handrails with a wax oil treatment which will be supplied. 2 coats are required on the decking & steps. Brushes and tools supplied. This task can only be carried out when the weather is good and dry and the wood has not been wet. Therefore timing is largely dictated by the weather.

2 x 1 metre chimneys need mortar render to stop leaks

Single storey bungalow 2 x 1 metre chimneys need sealing with mortar

Re render property and repaint inside property to remove the leak stains.

I need an experienced roofer or builder to inspect and repair damage around a dormer window and roof eaves area. There is damaged render and possible timber/fascia deterioration causing risk of damp and water ingress. Work may involve: • Roof inspection and repairs • Carpentry repairs to fascia/soffit area • External render repair • Checking flashing around dormer window Access will likely require scaffolding due to roof slope. Please provide experience details and availability for inspection/quote.

Caravan awning repair- there are some minor rips

Built in wardrobe door broken wardrobe doors have come off the hinges.

Old Mitsubishi car (2004), passenger door needs to be taken off, metal/steel plate needs to be welded on, door put back and attached to the metal/steel plate. It doesn’t need to be beautiful but I think you need a gas welder for this kind of work. We have had this work done already in the driver side - please see picture.