Find a professional fire door installation service in East London

6mm gap in door lock side. To comply with fire safety regulations, the gap must be between 2mm and 4mm. So door requires adjustment or a gap reduction seal added.

I need a fire door installed for a bedroom. Tasker would need a van to collect the door from the store and be able to add the handles and hinges also

The fire doors are already hung but no smoke seal strips have been installed . One door is in e70ar and the other door is in e153dp. Only 15 mins drive , I can drive you to the other location if required

The door handle is loose and when press down it doesn’t move the latch in for the outside of the door ( the inside of the door works fine).

We need to replace a door in our flat with a fire door which we will supply. The old door needs to be removed and disposed of.

fit a self-closing device on a flat front door, choose an overhead surface-mounted closer (like the Briton 121CE). Since flat doors are legally required fire doors, any device must be CE or UKCA marked and fire-tested to EN 1154/EN 163

Hello, I manage a flat council came for inspection and requested the following: Fire-Resisting Doors - Kitchen • Supply and fit in accordance with the manufacturers' instructions, self-closer, cold smoke brushes or seals and intumescent strips to the kitchen door, certified to FD30S standard. 2. Fire-Resisting Doors - all Bedrooms • Supply and fit in accordance with the manufacturers' instructions, self-closer, cold smoke brushes or seals and intumescent strips to all bedrooms door, certified to FD30S standard. In total 4 doors they are already all fire doors, chain self closer already on all doors but has been unscrews from previous tenant so need to adjust and screw back to one side so that door close itself properly. Regarding cold smoke brushes or seals and intumescent stripsn d to be fitted on all 4 doors seems like there is already something on top of the doors but will need to be done all sides I believe please provide quotes including material only thing needed : cold smoke brushes or seals and intumescent strips for 4 doors

• Supply and fit combined intumescent strips with integrated cold smoke seals (brush type) to the door edges — currently there is intumescent strip on the top edge only, so seals need adding to both vertical edges. Route into the door edge. • Refit/secure the existing self-closing devices — the closers are already in place but some fixings/screws are missing or loose, so they need re-screwing and adjusting so each door fully closes and latches. Please bring appropriate screws. Please include all materials in your quote (strips/seals and any screws/fixings). One of the doors is the kitchen door. I’ll need clear photos of each completed door edge for the council, and if you can provide a short written confirmation of what was fitted, that’s a bonus. Doors are all standard size, flat is on one floor, tenants in situ so minimal disruption please. Looking to book asap

Install certified fire doors

1. Fit new overhead door closers on 5 fire doors 2. Tighten overhead door closers on 1 door 3. Screw “fire door keep shut” signs on to 6 doors Must be able to guarantee your work for 12 months and available on 13 June.

5 standrd doors to be replaced with 5 fire doors, same frame to be used. The door stopper neeeds replacing

I need a certified fire door installer to replace my door please

Need 5 x fire doors installing (remove old doors / frames / architrave) and upgrade them to HMO fire door standard

I’m looking for a qualified professional to visit my property and check whether my door meets the requirements of a fire door. The task involves inspecting the door and confirming if it is a certified fire door (or advising if it is not). Ideally, the person should have experience or qualifications in fire door inspections, fire safety, or building compliance. If possible, I would like some form of written confirmation or brief report stating whether the door is compliant. Please only apply if you are properly qualified or experienced in fire door assessments. Location: RM10 9YU Flexible with date and time.

To put new fire doors in the kitchen

I need 4 fire doors changing I have the doors

Need fire door compliance certificate

I need someone to fit 6-7 fire doors and locks on each Please quote price per door The doors, hinges and hardware will be supplied

The screws you see here are loose so the entire deadbolt is coming off the door

6 self closing fire doors fitted with chains that have stopped self closing. One of them has a new overhead self closing system but still doesn’t self close. I think the tenants have been propping the doors open so the tension has loosened. I’d like to fit overhead door closers on all of the other five doors and the one on the 6th door needs looking at and fixing. Price is to take care of all doors to completion. I require a certificate and warranty - please let me know for how long the work is guaranteed and your experience with this. Job to be done on 7 February so let me know if you can make that date when responding. Thank you.