Find a professional fire door installation service in Central London

fit a self-closing device on a flat front door, choose an overhead surface-mounted closer (like the Briton 121CE). Since flat doors are legally required fire doors, any device must be CE or UKCA marked and fire-tested to EN 1154/EN 163

Hello, I manage a flat council came for inspection and requested the following: Fire-Resisting Doors - Kitchen • Supply and fit in accordance with the manufacturers' instructions, self-closer, cold smoke brushes or seals and intumescent strips to the kitchen door, certified to FD30S standard. 2. Fire-Resisting Doors - all Bedrooms • Supply and fit in accordance with the manufacturers' instructions, self-closer, cold smoke brushes or seals and intumescent strips to all bedrooms door, certified to FD30S standard. In total 4 doors they are already all fire doors, chain self closer already on all doors but has been unscrews from previous tenant so need to adjust and screw back to one side so that door close itself properly. Regarding cold smoke brushes or seals and intumescent stripsn d to be fitted on all 4 doors seems like there is already something on top of the doors but will need to be done all sides I believe please provide quotes including material only thing needed : cold smoke brushes or seals and intumescent strips for 4 doors

• Supply and fit combined intumescent strips with integrated cold smoke seals (brush type) to the door edges — currently there is intumescent strip on the top edge only, so seals need adding to both vertical edges. Route into the door edge. • Refit/secure the existing self-closing devices — the closers are already in place but some fixings/screws are missing or loose, so they need re-screwing and adjusting so each door fully closes and latches. Please bring appropriate screws. Please include all materials in your quote (strips/seals and any screws/fixings). One of the doors is the kitchen door. I’ll need clear photos of each completed door edge for the council, and if you can provide a short written confirmation of what was fitted, that’s a bonus. Doors are all standard size, flat is on one floor, tenants in situ so minimal disruption please. Looking to book asap

fire door to entrance of flat

Job is over now so leaving

Hi, we need to install the fire door to the kitchen. Please let us know if you have any experience with fire risk and understand the requirements. Materials will be provided.

I am looking for an experienced carpenter/builder to carry out several fire safety works following a fire risk assessment. The work required includes: • Install a 30-minute fire-rated (FD30) fire door to the kitchen. • Plasterboard the soffit, spandrel and understairs cabinet door using 30-minute fire-resistant plasterboard. • Provide ventilation to the gas meter cupboard at the base of the door in accordance with the recommendations: Create ventilation by undercutting the cupboard door along the full width at floor level to achieve an opening not exceeding 150 square millimetres (6 square inches). • Make good and finish all affected areas. Please provide: Your experience with similar works. An estimated timescale. Your quotation- labour only.

1. I have 7 fire doors that require a third fire rated hinge on all doors. They need to be BS EN 1935 compliant. 2. The doors also need need to be fitted with intumescent strips on all 7 doors. 3. Each door needs to be fitted with compliant overhead door closer. 4. Box in electrics and cables using fireproof boarding.

I need a skilled carpenter to repair a damaged timber door frame and hang a new solid oak fire door. The door is heavy (42kg), so I am looking for someone with the appropriate tools and experience. Scope of Work: 1. Remove and dispose of old door 2. Structural Frame Repair: The current timber jamb is badly splintered at the strike points as a result of a locksmith needing to use force to break in (see photos). Needs a professional repair so the frame is structurally sound again. 3. Door Hanging: Hang a new Victorian 4-Panel Oak FD30 Fire Door (1981mm x 838mm x 44mm). Trim as needed - the floor is uneven and will need some trimming, and likely a timber threshold strip fitted to manage the gap on the high side. The door has 20mm solid oak lippings to accommodate this. 4. Hardware Installation: - Install 3x Grade 13 hinges - Consolidate Locks: Remove three existing locks from the old setup. Re-install only ONE insurance-approved ERA BS3621 5-Lever Sashlock and its matching strike plate (pictured) into the repaired frame. - Install new lever handles (57mm centers). 5. Finishing: Ensure the 44mm door sits flush in the 46mm frame rebate. Patch/fill the old lock holes in the frame so it is ready for sanding/painting. Materials Provided: - Solid Oak Fire Door (42kg) - 1981mm X 838mm X 44mm - 3x Grade 13 Ball Bearing Hinges - Heritage Brass Lever Handles. - Existing ERA BS3621 Sashlock & Strike Plate (pictured) Tasker Requirements: - Must provide own professional tools - Must provide timber, professional wood glue etc for the frame repair. - Experience with heavy solid-core doors Photos: Please see attached for the current frame damage and the hardware being reused.

1. Fit new overhead door closers on 5 fire doors 2. Tighten overhead door closers on 1 door 3. Screw “fire door keep shut” signs on to 6 doors Must be able to guarantee your work for 12 months and available on 13 June.

I need a handyman for several jobs in my home: * Supply and fit 1 internal FD30 fire door (living room) – door will be provided * Fit/replace door handles on 3 internal doors (kitchen, bedroom x2) Budget for labour is around £180–£220 depending on scope. Please only reply if you are able to work within this range.

Need 5 x fire doors installing (remove old doors / frames / architrave) and upgrade them to HMO fire door standard

I need an intumescent strip combined with a cold smoke seal installing on my flat front door / door frame.

I need fire rememdial works on an inward opening flat door to ensure hinges sufficient for a self closing mechanism. I already have a fire assesment form to help identify what is needed.

I have 2 x fire doors, which have already been removed. I need someone to come and take them. You can either dispose or keep them. 1st Floor apartment. They're heavy and will probably need two people to take them down the stairs.

Fire doors to be installed, Frames installed but one side left unfixed for you to adjust , Ironmongery to be fitted , Architrave to be fitted All doors are finished Must have all tools

Please share quote even if the price is higher than my proposal. I need 4 fire doors fitted in my property. A basement flat. Existing doors to be removed and replaced with fire doors and frame presumably. Supply and fit preferred . To be installed with locks.

Carpentry. 1. Replace 4x bedroom doors and frames to FD30 fire doors. Please supply the frames and doors. 2. Two further doors (kitchen and living room) are already FD30 rated, however fire assessment has identified the door to frame gap is not to spec: some remedial work required here. Budget expectation not including cost of the new doors themselves.

The screws you see here are loose so the entire deadbolt is coming off the door

We need to install a door closer to an internal fire safety door.