Find professional electric boiler installation & repairs in London

Hi looking to get a quote for gas registered plumber to alook at my glowworm 15hx boiler which keeps coming up with error code f22 and f25 but tends to fire up in the end after a reset or to and also is leaking small amount when in use also looking to get a few other bits fixed at the same time 1. An under sink waste leak in kitchen 2.looking at maybe getting a InSinkErator Standard 460 Food Waste Disposer installed if possible 3.repalce of towel radiator haven't got replacement yet but looking for similar happy to go and buy one of have it supplied

Magnaclean filter on gas boiler is leaking/dripping Seems to be from where the lid fit on, ie the rubber seal.

I need a professional to install a new thermometat for Worcestershire Bosch boiler

The sensor light in my boiler cupboard isnt working properly and keeps going on and off at random times. I need that repaired please.

I need someone to reconnect my nest dial to my boiler

## Carpenter's Brief – Bespoke Kitchen Cupboard Storage I would like a bespoke internal storage system fitted into a former boiler cupboard (no functioning boiler). **Approximate dimensions:** - Internal width: 1300 mm - Clear door opening: 1000 mm (centred) - Height: 1300 mm - Depth: 600 mm - Approximately 150 mm concealed either side of the opening. All measurements to be verified on site. ### Proposed Design A robust, fixed cabinet with **two vertical sections and ideally six independent pull-outs**, designed to maximise accessible storage. **Left section – Cookware** - Top: Pull-out with adjustable vertical dividers for frying pans and lids. - Middle: Deep, reinforced drawer for saucepans. - Bottom: Deep drawer for mixing bowls and colanders. **Right section – Appliances and Trays** - Top: Storage for smaller kitchen equipment. - Middle: Pull-out shelf for appliances. - Bottom: Vertical dividers for baking trays, roasting tins and chopping boards. Heavier appliances and cookware should be positioned at lower levels. Final

Task: Diagnose and Replace Wireless Thermostat – Glow-worm Boiler I have a Glow-worm Ultimate 30c combi boiler with a wireless thermostat that has stopped working reliably. The thermostat screen is intermittently blank, and the heating won’t come on when the display isn’t working. I’ve replaced the batteries and completed basic troubleshooting, but the issue persists. I suspect the thermostat needs replacing, potentially along with the receiver. I’m looking for a qualified heating engineer who can: * Advise on which replacement thermostat and receiver to purchase, ensuring compatibility with my boiler. * Check whether both components need replacing. * Install and pair the new equipment, and test the heating. I can purchase the recommended equipment in advance once compatibility is confirmed.

I need my boiler to be serviced and certified

i changed heating element and burnt switch but still no hot water which means heat exchange unit is broken for my dual boiler .

Ii need a thermostat receiver wired

Current wiring is faulty as boiler always fires up 24/7. Wiring needs fixing

Boiler pressure is low. Heating is weak, hot water seems to be fine. Not an emergency but help needed

No hot water and pressure is down.

Hello, I need a boiler service certificate for a boiler in my restaurant. I believe the boiler itself is a domestic-type boiler, although it is installed in a commercial property. I have attached a photo of the boiler so you can check. The boiler is working perfectly fine. My main reason for arranging this is that my landlord has asked me to provide a valid boiler service certificate. I would therefore need the inspection/service to be carried out by someone who is properly qualified and authorised to issue a valid certificate. I would prefer not to have unnecessary work carried out on the boiler since it is working fine, but if servicing is required in order to issue the certificate, that is absolutely fine. Could you please let me know if you can do this and how much you would charge? Thank you.

I have checked and is in working order, all the status lights are green which indicate the hive is connected and working and the same for the boiler as we have hot water. However the thermostat still does not send signal to heat up

Have recently had boiler installed and contractor had to cut out a small hole in ceiling for new flue. Need someone to re plaster the ceiling - also open to offers for those who can re plaster and paint in the same day

Boiler Service and Smart Thermostat Replacement I’m looking for a qualified heating engineer to: * Carry out a full boiler service. * Remove the existing old heating controller. * Diagnose why the heating/boiler seems to switch on unpredictably. * Install and configure a new smart thermostat Drayton Wiser Wireless Heating The new thermostat has already been purchased. Please include any required testing and confirm the system is working correctly after installation.

I need a plumber to re-pressurize my boiler and to tighten the bathroom heater as it’s leaking at 8 AM on the 9th July 2026 please. I have guest staying in my flat and the only time they can do is 8 AM tomorrow morning.

You must be a plumber or a heating engineer. Boiler diagnosis completed as follows below and need someone to replace both parts. Parts to be ordered separately and not included in price here. - system pressure was low. I topped up the pressure and reset the boiler; however, the boiler still failed to fire. The appliance was displaying the fault code shown in the photographs provided. I referred to the manufacturer's instructions, which identify this fault as relating to the gas valve. I then contacted the manufacturer directly to confirm, and they advised that the fault is associated with the gas valve and ignition electrodes, with replacement of these components being the recommended course of action. The active fault codes displayed on the front of the boiler provide a clear indication of the fault condition being detected by the appliance, and the manufacturer has confirmed that these codes relate to the gas valve and ignition electrodes.