Find professional thermostat installation near you

Install a tado thermostat Note...I currently have a v2 nest thermostat I have the new thermostat Note - The Tado bridge and temperature sensor are already set up The tado 3 thermostat needs 4 wires connected which i assume match the 4 wires that connect to my existing nest 2 thermostat

Looking for a qualified and Gas Safe registered heating engineer with experience installing Hive smart thermostats to connect a Hive system to my existing combi boiler. There is currently no thermostat installed, so this will be a new installation rather than a replacement. The job involves fitting and wiring the Hive receiver to the boiler, setting up the wireless thermostat and ensuring everything is working correctly. I will supply the Hive thermostat and receiver as per the attached image.

Hi, I’m looking to swap my Nest Learning Thermostat 3rd Generation for a Nest Learning Thermostat E and would like to split my radiators back into two separate heating zones: upstairs and downstairs. The heating was previously set up in two zones, but one radiator was connected incorrectly, so I ended up combining everything onto one thermostat. My current Nest 3rd Gen thermostat is now having software issues, and I need to return it. I’d like to install the Nest Thermostat E and restore the two-zone setup, with separate controls for upstairs and downstairs. Could anyone advise me on whether this is possible and what would be needed to get it set up correctly? As i am having combi boiler and 3 generation nest is not very useful for me . Thanks in advance!

We have a nest thermostat with hot water control setup already. Needs to be replaced with a tado x. Boiler sits outside and already wired to the heat link inside for the nest.

Replace the existing wired Honeywell thermostat with a smart wireless thermostat with app control. The heating system has two separate zones (upstairs and downstairs), each controlled by an existing Honeywell motorised zone valve located next to the Worcester boiler. I would like the new wireless thermostat/receiver installed and connected correctly to the existing heating system and zone valves.

Hi I need an Electrician to fix my smart thermostat. Please only get in touch if you have experience in installing smart thermostats to boilers. The Thermostat always worked, but I recently had my boiler changed, and now the controls don't adjust the boiler anymore. I will have a new one handy if it is believed that the old one is faulty and it's not just a wiring issue

Looking for a Gas Safe registered heating engineer to install a Hive smart thermostat on an Ideal Independent Combi 24 boiler. I will supply the complete kit, including thermostat, receiver and hub. There is an existing mechanical timer but no room thermostat. The job includes fitting and wiring the receiver, pairing the devices, configuring the existing timer and testing the heating and app control. Location: Brixton Hill, London Budget: £120 Please quote a total price including any materials and VAT, and confirm your availability and Gas Safe registration.

Looking for an electrician to swap out two old Ambiente thermostats on a wet underfloor heating system. I’m supplying the replacements (Heatmiser NeoStat V3). Straightforward like-for-like swap with no rewiring needed.

Install tado smart heating (2 thermostats) + small plumbing fixes – Lee, SE12 Description: I’m upgrading to tado X smart heating in a 4-bed end-terrace house in Lee, London SE12, and need a qualified heating engineer or electrician to install it. I’ll supply the tado hardware. My current setup: Gas boiler in the loft. A wireless Horstmann thermostat for the radiators upstairs. Its transmitter is dead, and its receiver is wired to the boiler on the second floor. Wet underfloor heating on the ground floor, with its own manifold, Grundfos pump and mixing valve, controlled by a wired Heatmiser thermostat that only switches the pump. The underfloor heating can’t fire the boiler on its own; it only works when the upstairs heating is on. What I need done: Replace the Horstmann receiver with a tado Wireless Receiver X, wired to the boiler, and set up the tado Wireless Smart Thermostat X. Replace the wired Heatmiser with a tado Wired Smart Thermostat X to control the underfloor pump. Please confirm it can switch the pump directly, or fit a relay if needed. Set things up so the ground-floor underfloor heating can call the boiler independently through the tado system. Advise whether a zone valve is needed on the underfloor flow, and fit one if so (please quote separately). Inspect and reseal some weeping joints on the underfloor manifold. There’s green corrosion around the isolating valves and mixing valve. Quick check that the radiator valves (7 radiators) will accept tado smart radiator heads, which I’ll fit myself later.

Would like someone to give me an price for installing a smart thermostat for boiler and take the old one off

Hi, There is no power in my thermostat need an electrician to fix this power/wiring issue

I would like a Google nest thermostat installed, both the electrical side and into the boiler.

Replacing old thermostat (Honeywell) with a new smart heating control system (Hive v4)

The entire flat is using the under floor wet heating. The old thermostat is broken. Model number: UFHDIALB I ordered the same replacement. Need to replace it and seal with silicone to make it looks nice. I am available from 7pm on Wednesday. Please let me know your availability. And or if you need more information. Thx

I have two Hive thermostat mini modules, two receivers and one Hive hub. I have moved into the property after previous tenants and it seems the modules were registered with the previous tenants. I would like to reset the modules so I can access them in my hive app.

I have checked and is in working order, all the status lights are green which indicate the hive is connected and working and the same for the boiler as we have hot water. However the thermostat still does not send signal to heat up

Hi! I need an experienced plumber or handyman to replace the concealed thermostatic valve element in my shower (Scudo brand). Part: The replacement thermostatic element is already purchased and on-site. Access: The existing shower system is a concealed valve setup. Photos: Provided Requirements: - Please bring your own tools and white silicone sealant will be required. - You must have experience working with concealed thermostatic shower valves. - Please ensure the water is turned off safely, the element is swapped cleanly, and the seal is tested for leaks and temperature control before finishing. Thank you.

I have the boiler installed but I need to install the thermostat to control the temperature. The boiler is a Greenstar 4000 and the thermostat is a Honeywell T3.

Boiler Service and Smart Thermostat Replacement I’m looking for a qualified heating engineer to: * Carry out a full boiler service. * Remove the existing old heating controller. * Diagnose why the heating/boiler seems to switch on unpredictably. * Install and configure a new smart thermostat Drayton Wiser Wireless Heating The new thermostat has already been purchased. Please include any required testing and confirm the system is working correctly after installation.