Find professional electric boiler installation & repairs near you

We have had no hot water or central heating for several weeks and need someone to diagnose and repair the system. We have: Baxi boiler Elson Zircon 210i, 210-litre indirect unvented hot-water cylinder Google Nest controlling the heating and hot water Please only respond if you are experienced with Baxi boilers, unvented hot-water cylinders and motorised valves/central-heating controls. Will provide any pictures required.

Gas Safe registered engineer required in Edgware HA8 to inspect an Ideal Logic Combi2 C24 installation following a Gas Safe Register inspection. The task is to carry out an on-site technical assessment and provide a detailed written remedial report. The report should explain what work is required to make the installation safe and compliant, identify any suitable interim remedial solution where appropriate, set out the proper permanent remedial solution, provide estimated labour and material costs for each, identify any additional defects found, and investigate an intermittent loud banging noise from the boiler. Existing Gas Safe Register and Ideal Heating technical documentation will be available for review. I am only considering established UK limited companies. The business must be currently Gas Safe registered for the relevant work, appropriately insured, and able to provide its registered company name and Companies House number for verification before appointment. No remedial work is required as part of this task. The deliverable is the site inspection and written technical remedial assessment. All communication must remain in writing through Airtasker.

Hello, I need a boiler service certificate for a boiler in my restaurant. I believe the boiler itself is a domestic-type boiler, although it is installed in a commercial property. I have attached a photo of the boiler so you can check. The boiler is working perfectly fine. My main reason for arranging this is that my landlord has asked me to provide a valid boiler service certificate. I would therefore need the inspection/service to be carried out by someone who is properly qualified and authorised to issue a valid certificate. I would prefer not to have unnecessary work carried out on the boiler since it is working fine, but if servicing is required in order to issue the certificate, that is absolutely fine. Could you please let me know if you can do this and how much you would charge? Thank you.

My boiler has packed up, I need the boiler which is a combi 25 to be replaced Either quote for supply or labour only

Boiler Cupboard Door Replacement The door to boiler cupboard is damaged and needs replacement. Hinge and frame may also need some work to ensure door is secured properly.

Need a new boiler supplied and fitted. Don't need a powerful one as this is for an out building with one shower so no need for an expensive one. But has to be reliable. Open to installation only quotes too. It will be at the same location ... horizontal flue out the wall.

I have checked and is in working order, all the status lights are green which indicate the hive is connected and working and the same for the boiler as we have hot water. However the thermostat still does not send signal to heat up

We would want to install a brand new boiler tap near the kitchen sink. Its a first time installation

I need a qualified boiler/heating engineer to check and fix my boiler, as the hot water is currently not working. Ideally, I’d like the problem diagnosed and repaired during the visit if possible. If parts are needed or there will be additional costs, please let me know before carrying out the work.

Modify boiler cupboard. Repair corner join, Fit base under unit

Airing cupboard has a burnt sulphur smell and making an unusual noise. Investigate and fix

I have a removable panel in the kitchen that covers the pipework underneath the boiler. It can be removed when the boiler needs servicing and then reattached using magnets. I may need to have a magnetic filter installed on the boiler pipework, which will take up some additional space. As a result, the existing panel may no longer fit back into position. I am looking for someone who can replace the side section of the panel with a wider piece of wood, so that the panel can still be used to cover the pipework neatly without leaving a gap. Please let me know if this is something you could do.

Worcester boiler, on the attic needs to be re-pressured

I would like my boiler to be boxed up from top to bottom, you will need to provide materials

Gas Safe Engineer needed for: Vaillant boiler, F.75 fault. Pressure is 1.7 bar, gas supply is working, reset has been attempted, and there's no hot water Free parking. Please say when you are available with your quote

Have recently had boiler installed and contractor had to cut out a small hole in ceiling for new flue. Need someone to re plaster the ceiling - also open to offers for those who can re plaster and paint in the same day

Boiler Service and Smart Thermostat Replacement I’m looking for a qualified heating engineer to: * Carry out a full boiler service. * Remove the existing old heating controller. * Diagnose why the heating/boiler seems to switch on unpredictably. * Install and configure a new smart thermostat Drayton Wiser Wireless Heating The new thermostat has already been purchased. Please include any required testing and confirm the system is working correctly after installation.

I need a plumber to re-pressurize my boiler and to tighten the bathroom heater as it’s leaking at 8 AM on the 9th July 2026 please. I have guest staying in my flat and the only time they can do is 8 AM tomorrow morning.

You must be a plumber or a heating engineer. Boiler diagnosis completed as follows below and need someone to replace both parts. Parts to be ordered separately and not included in price here. - system pressure was low. I topped up the pressure and reset the boiler; however, the boiler still failed to fire. The appliance was displaying the fault code shown in the photographs provided. I referred to the manufacturer's instructions, which identify this fault as relating to the gas valve. I then contacted the manufacturer directly to confirm, and they advised that the fault is associated with the gas valve and ignition electrodes, with replacement of these components being the recommended course of action. The active fault codes displayed on the front of the boiler provide a clear indication of the fault condition being detected by the appliance, and the manufacturer has confirmed that these codes relate to the gas valve and ignition electrodes.

There’s a gap beneath my boiler that needs to be covered as it’s a possible entry point for mice. The pest control company has asked for a Perspex sheet to built and siliconed in place around the boilers paperwork. Would need to be custom fitted and make w a jigsaw. Thanks