Find a sockets and switches installation professional near you

3x Shelly 1pm for towel rails 1x Doorbell Transformer 1x Smart Doorbell Tapo D235 1x Power socket 9.15-11.45am, 12.45-3.30pm or 5.30pm onwards Old Jamaica Road SE16 https://shellystore.co.uk/product/shelly-1pm-mini-gen4/ https://www.tp-link.com/uk/support/download/tapo-d235/ https://www.amazon.co.uk/dp/B0GQGH8SLK

Qualified electrician required for lighting alterations in a three-storey house. All existing lights/switches are live and working. Hallway/stairwell switches Replace/reconfigure 4 switch plates using Click MiniGrid + Quinetic for a consistent look, retaining wired switching where practical and adding RF only where needed. Final controls: • GF front door: outside light + GF hallway • GF bottom of stairs: GF hallway + 1F landing • 1F landing: GF hallway + 1F landing + 2F landing • 2F landing: 1F landing + 2F landing GF hallway already has 3-point 2-way/intermediate switching. 2F landing light already has 2-way switching. For the 1F landing light, retain the existing wired 1F switch and add 2 Quinetic RF controls at GF bottom of stairs and 2F landing via a QURWM3 hybrid receiver. Proposed switch kit is NOT YET ORDERED. Please confirm compatibility/quantities before I buy. Work includes: • Confirm existing hallway switching so correct 2-way/intermediate modules are fitted • Install 4 matching faceplates/modules • Install/connect QURWM3 receiver and existing wired 1F switch • Pair/test the 2 RF switches and all lighting No new chased switch wiring between floors. Stairwell wall light Replace existing working fitting with supplied Alabaster Stone Diffuser Wall Light. Allow for drilling/new fixings if needed. Ground-floor hallway light Remove existing working track lighting and install supplied Interiors 1900 Fargo 3-Light Large Inverted Pendant. Requires cable routing approx. 3m across ceiling using cable/wire fishing, with a few strategic access holes if needed. Please minimise ceiling damage. Making good/plastering/painting not required. I supply both light fittings and, once confirmed, switch kit. Please supply normal sundries/cable/fixings. Ladder available onsite. Please confirm experience with 2-way/intermediate circuits, Quinetic/Click MiniGrid, and cable fishing.

Change 4 light switches and 4 lights bulbs. Change switch from touch to dimmer switch

Two bed cottage with 4 x lights to be fitted (one light switch to be connected) and 4 x plug sockets to be changed. This is an old property with an old system, making safe to sell property.

Fit two new plug sockets into the wall

I need a qualified electrician to find out why some of my sockets are not working including my electric cooker socket. I also need to know if getting a 240w dehumidifier will trip the wiring.

Chasing/recessing 4 existing sockets in to wall. Moving living room light to the centre of the ceiling and fitting a light fixture in hallway above stairs.

Trying to fit new sockets in the wall. Backbox is too small and needs to be extended back a bit more. Need 3 sockets to be fitted so 3 backbone to be extended back.

I’m looking for a qualified/experienced electrician to replace my existing vintage light switches with smart WiFi switches. There are 3 x 1-gang switches and 1 x 3-gang switch to be replaced. The existing wiring appears not to have neutral wires at the switch locations, so the appropriate capacitors/bypass modules may need to be fitted where required. I already have all the smart switches, capacitors and a spacer available. I can provide photos of the existing switches and wiring before the job if helpful. Looking for someone experienced with smart switch installations who can safely install, test and configure the switches.

Two wooden lamps with very old wires/switches and plugs, both need replacing.

I have had whole house rewired and just need 2 more sockets added in one of the rooms next to an existing socket.

I have two double light switches that are sticking in the “on” position. I also have a door handle to the outside balcony (lockable door) where the handle comes loose when pulled.

Installing two electrical sockets in bedroom

We have 3 set of sockets which need moving approximately 100 to 150cm aside. Could you please check and quote. There are Wadrobes going in those places 1) On the image where there is bathroom. I have marked black line. On the right side of that black line towards bathroom door we would like to move those sockets. ((2x) 3 pin socket board and openreach network socket board need moving right side of the black line. 2) On the image where there is standing fan wardrobe is going in it. From the wall where sockets are towards black lines on both sides. So a tricky place since on right there is radiator and on left it’s storage room wall. But we would like move the socket even if it’s moved to little odd place. In this set there are ((2x) 3 pin socket board, TV cable line socket, open reach network line socket) 3) there is one (2x) 3 pin socket board which needs moving 30cm. Currently going behind bed headboard. Image not included but it’s straightforward wall move.

To change over 5 existing light sockets to new 5 light sockets.

Replace 4x double switches for double dimmers

Power sockets are burning when you plug.

**Description:** We’re looking for a qualified electrician to carry out some work in our flat before Friday (ahead of decorating). **Scope of work:** * Install 3 new plug sockets * 2 in a bedroom * 1 in a cupboard * Run cabling for 2 wall lights (sconces) above the bed (installation of fixtures not required at this stage, just wiring) **Timing:** Ideally completed before Friday **Location:** Flat next to Brixton O2 Academy **Additional details:** * Access is straightforward * Happy to discuss best positioning if needed * Please bring all necessary tools and advise if any materials are required **Requirements:** * Qualified and experienced electrician * Able to complete work safely and to standard Please get in touch with availability, a rough quote, and any questions. We don't have materials.

Minor electrical work: 1. move a light to centre of the room (4 spotlights already capped) 2. Cap off two spotlights and move to centre of a room 3. Cap off one unnecessary wall switch ready for covering 4. Remove trunking/spotlights and put in regular ceiling light Can talk through the job in person but the red rings on the photos show approx what needs to be removed/installed