Find a professional balustrading contractor near you

We need wiring installed to our existing external timber balustrade. Please see photos of the area now. Last photo shows what we are after. Measurements below Larger balustrade is 4870mm wide, 1000mm high Smaller balustrade is 2745 wide, 1000mm high We can supply wire kit from Bunnings

Looking for an experienced handy person or carpenter to repair or replace the bottom timber rails across 4 panels of a deck balustrade. Must have experience completing similar balustrade repairs. You will need to supply tools and materials.

Rotted wood on part of balustrade needs to be repaired (rotted timber replaced)

Looking for someone to install balustrade hand rail and wire. Can supply to balustrade wire and posts if needed

Would like a quote on restoring the balustrade Also, how long will it take.

I need to tighten fence balustrade metal wires as well as replace one in the hand rails of the steps to my home. Photos attached.

Centre spine staircase requires stainless steel & wire balustrade

The safety wall on my balcony needs to be extended. I need a carpenter to frame and extend the height on the existing wall, making it ready for renderer to complete the remaining work. Total length of wall 19 metres Current height : 50cm Once completed : 1.3m

I need a timber stair balustrade removed carefully. The job includes: * Remove the entire timber balustrade (vertical posts and top rail) shown in the photos. * Remove fixings (screws/bolts/nails) where possible. * Minimise damage to the existing timber capping and surrounding walls. * Stack all removed timber neatly (or dispose of it if agreed). The balustrade is approximately 2–2.5 metres long. Important * I believe this is not structural, but please inspect before commencing. * If you believe it provides structural support, stop work and discuss before proceeding. * Care is more important than speed. * Please bring your own tools (multi-tool, pry bars, drill/impact driver, etc.). Preferred experience * Carpenter * Handyman experienced with timber balustrades * Cabinet maker also suitable Questions for Taskers 1. Have you removed similar balustrades before? 2. Will you minimise damage to the timber capping? 3. Can you dispose of the timber if required? 4. Approximately how long do you expect the job to take?

Hi Existing metal balustrade on front verandah needs a repaint. Have scratched most of the rust away where it was flaking and just needs some fresh paint. 2 coats, paint supplied as I’ve already bought it. It’s not the Mona Lisa, just needs a better brush hand than what I’ve got. Banyo location, earlier the better.

Stair balustrade to be painted (light sand, primer, gloss white x 2 coates). Perspex will be removed

Replace rotten lower hardwood balustrade rail only x2. Existing post is sound. Reuse existing balusters if possible. Supply matching hardwood, install, prime all cut ends. Painting not required. Price negotiable

We have just raised the height of a balustrade beside a set of external stairs through on-site steel welding. The task now is wire brush the welds to remove any rust and scale, prime all new weld joints and then to paint the balustrade black (monument). This only applies to the new, raised section of the balustrade. The photos show the that balastrad looking down and then looking up as well as a typical welded joint that need to be prepared. The photos also show the lower balustrade already painted black and needing no further work and the new upper work which has been primed grey. There is also some new infill bars in the old section shown in the photo looking up the stairs that need to be painted.

Timber base board and uprights have rotted. Need a qualified handyman to be able to remove the base boards (two of them) and then replace all of the uprights including the three long ones in the middle, finally replacing the base boards with new timber Price negotiable and suitable timber will be supplied with your guidance.

Install aluminium balustrade inc. collection from Bunnings We need someone to collect and install an aluminium balustrade. Materials purchased by us upfront — you will not be out of pocket at any point. What you need to do: - Collect ProtectorAl aluminium fencing components from Bunnings (we will purchase and arrange) - Install on site: 2800mm straight run + 1000mm return at 90°, mounted to top of masonry wall (approx measurements). - 4 flanged posts dynabolted to masonry, 3 panel sections (2 panels cut to size between pickets) Tools required: hammer drill + 10mm masonry bit, angle grinder or hacksaw for cutting aluminium, level, basic hand tools. Materials: Purchased by us upfront Please check the photos before quoting.

Install a frameless standoff glass balustrade using materials I supply on site. Balustrade is located more than 5m above ground level, so it must be installed and certified to AS 1288 / AS/NZS 1170 by a suitably qualified and licensed tradesperson. Materials on hand: • 15mm frameless standoff glass panels: 850W × 1280H ×6, and 750W × 1280H ×3 • Summit 30×21mm Nanorail Deluxe handrail 5800mm (satin) ×2 • Summit Nanorail Deluxe rigid glazing rubber 2900mm ×3 • Summit 30×21mm Nanorail Deluxe wall plate extended (satin) ×6 • Summit 30×21mm Nanorail Deluxe 90° joiner (satin) ×1 • Glass standoffs 38×25mm (satin, SS2205) ×48 Note: fixing rods are NOT supplied — please include any missing items in your quote. Scope: • Labour-only install of the above into the existing structure, glass 15mm toughened with Nanorail top rail fixed into structure • Confirm supplied standoffs and fixing details suit 15mm panels for a balustrade above 5m per AS 1288 before commencing • Flag anything missing or any recommended change to the fixing approach prior to install • Provide a Certificate of Compliance on completion from a licensed/qualified trade, expressly noting the balustrade is more than 5m above ground Requirements: • Appropriate trade licence and insurance — please state licence number • Quote labour only; advise availability and lead time Site: inner Sydney. Please confirm you can certify to AS 1288 at this height before quoting.

Experienced carpenter required to repair two balustrade/handrails that have rotted on our front outdoor stairs. Materials and labour must be included. Quality hardwood must be used.

Front of House Balustrade and back balcony Balustrade - total of Approx. 18 - 20m. Simple straight line balustrade (to be painted black). Paint will be supplied - need someone to prepare, prime and paint before the 1st May 2026 (latest 5th May). Any questions, just ask. Would love the help. Thank you!

I’m looking for an experienced tradesperson to install a stainless steel wire (cable) balustrade on my internal staircase. Holes are already drilled and aligned

We are moving house and need someone to please instal some wire for the Balustrade/Deck. We have the wire. All holes are already in the timber, all measure ready to go :) This is quite urgent so would love someone in the next week or so to complete this.