Find a local timber flooring profesional in NSW

There is a guage/hole about 5cm long in my floor that I need repaired please.

2 decks One is 9x4mtr with 2.5 metre wide 8 tread staircase one is 13x1.5 metre with 2 x 1.5 metre wide staircases 8 tread Staircases are pine deck is hardwood Need thorough clean and prepare apply deck oil and stairs Raised nails - will likely need hand sand previous oil used had paint tint needs clean and likely light sand without damaging nails

I’m looking for a carpenter or decking professional to repair and restore my existing front timber deck. 1. Repair the existing three timber steps at the front of the deck. The timber is weathered and worn, so I’m looking to have the steps repaired and any damaged or deteriorated boards replaced as needed. 2. Add an extra step to the side steps. 3. Sand back the decking and apply a decking oil or stain to restore the timber and provide protection against the weather.

Clean and re-stain timber deck under gazebo. Clean, re-stain timber storage unit and replace wheels.

Note: this is a re-stain, not a paint job. I want a penetrating deck stain or oil that shows the timber grain, not a solid paint coating. Hi, I'm looking for an experienced deck finisher to restore two timber decks at my home in [suburb]. Areas: • Front entry/porch deck: about 3.94m deep x 4.6m, with a picture-frame border and a step edge • Alfresco deck: about 4.3 x 5.9m Current condition: The decks have a dark brown finish that has worn and faded in high-traffic areas, and some boards are weathered. Photos attached. Scope I'm after: • Clean the decks properly (deck cleaner or pressure wash) • Sand back to an even surface • Apply 2–3 coats of a quality exterior decking oil or stain in a [dark brown / similar colour to current] finish • Protect the surrounding walls, door threshold and rendered planters • Leave the site clean Please include in your offer: • Whether your price includes materials, and which product you'd use • Whether you recommend 2 or 3 coats and why, and how long the job will take, including drying time • Photos of similar deck jobs you've done • Any repairs you notice are needed, such as loose or damaged boards Timing: Flexible, ideally within 2–3 weeks, weather permitting.

Timber floors need to be repaired due to some white ant damage and other wear. (All pests have been eradicated) needs to match existing jarrah boards Timber floor is 80mm x 20mm boards. 10 x boards nominally 1300mm long need to be replaced . Need to include removing skirt boards etc and re fixing on completion. Need to sand and refinish repair. Exclude painting

Rubbish removal - painted decking boards and some other timber from deck replacement. Cut up ready for removal. Access is level via house side passage. You can use carport for a small ute. The deck is 3.3 X 3.8m . All the boards were removed plus half of bearers/joists etc.

Rest of timber deck to the corner needing to be completed. Pots to be moved. • Supply and install treated pine subframe, including posts, bearers and joists. • Install joists at the required centres to suit the decking span. • Supply and install all stirrups, bolts, brackets, joist hangers and fixings. • Level and align the completed frame ready to receive decking. Decking • Supply and install approx 90 x 19 treated pine decking boards. • Fix all boards at consistent spacing throughout. • Finish all edges, trims and fascias as required. Painting • Prepare, sand and clean all decking and exposed framing ready for painting. Apply exterior primer and decking paint to the whole deck including exposed framing so all is the same colour.

3x 3.8m room grind and polish required

I have a small section of floorboards (380 × 680mm) that is open and needs to be filled with matching boards. I have the matching leftover floorboards ready to use in sizing 330x2100mm I need an experienced flooring/carpentry person to cut the boards to size and securely install them so the finished section is neat and level with the existing floor.

Holes on engineered timber flooring, need to repair. Pls help! We are ending our lease and need to patch these up, 2 of them still have the screw inside, they need to be pulled out, filled and colour matched with the floor. There are 9 holes in total.

Small section of timber flooring needs to be installed. This will include purchasing floorboards, install them and staining them ensuring they match the existing flooring. Subfloor may also need to be replaced. Happy to negotiate price pending scope

I recently had a hot water leak in the laundry that spilled into the adjoining kitchen / hall area. At the time, all visible water was removed and professional dehumidifiers /dryers were used, so I believed everything had dried properly. I was then away overseas and have just returned to find that sections of the floating timber flooring have started to buckle/lift and gaps have appeared between some boards. Approximately 5-6 boards are affected. They also had a heavy piece of furniture pushing pressure onto it which may have contributed to the uneven expansion / shrinkage. The floors were already older / not in perfect condition, so I’m not looking to replace the entire floor. I’m hoping to salvage and repair the existing boards wherever possible. I’m looking for an experienced timber flooring specialist who can assess the affected area, including checking the timber and underneath for residual / trapped moisture. I understand the repair may need to be completed in two stages: initially lifting / removing the affected boards so the area underneath can be properly inspected and, if necessary, allowed to dry completely; then returning once moisture levels are appropriate to relay / reseat and repair the existing flooring. Ideally you will have a moisture meter and experience with water-damaged floating timber floors. The priority is making sure everything underneath is properly dry before the floor is closed back up, while preserving as much of the existing flooring as possible. I have availability this tomorrow (Sunday). Thank you

I have ripped up all of the old carpet from four rooms but need someone to remove all of the staples around the edge of the rooms and clean the floors so they are ready to be oiled

Replace a broken timber on my deck. Supply and install. No need to stain or lacquer. Timber is around 1.2m long

Approx. 27 m long × 2.5 m high (approx. 67.5 m²), one visible side. Scope: • Thoroughly clean and prepare timber • Sand weathered/rough areas and provide an even finish • Apply two coats of supplied exterior Merbau timber stain/oil, following manufacturer instructions • Protect paving, plants, pool glass and adjacent surfaces from dust/stain • Include all labour, drop sheets, masking and cleanup etc Materials and equipment supplied including hand sander, stain and applicator. Please quote based on experience with Merbau/timber screening and advise estimated duration. Photos attached.

Multiple small gaps in floorboards , need small gaps filled with wood coloured gap filler. House is on piers- easy access. Easy job- I can’t do it as I’ve just had surgery.

The handrail has already been mostly prepared. I just need someone with the right tools and attention to detail to carry out the final sanding so it's smooth and ready for staining or clear coating.

Repair these chips in the timber floor for a commercial office move out

Fixing floor scratches on floor