Find a professional hot water system contractor in Melbourne

Rinnai B26 Continuous Flow Hot Water System Diagnosis - Mentone VIC Looking for an experienced gas plumber familiar with Rinnai continuous flow hot water systems. Unit is a Rinnai B26 (manufactured 2013). Symptoms: • Hot water failed while a bath was running. • Unit will restart after power cycling. • Ignites and produces hot water. • Runs for approximately 10 seconds then shuts down. • Power remains on. • No circuit breakers are tripping. • Outdoor powerpoint has been ruled out by testing from an alternative power source with the same result. Looking for: • Fault diagnosis and repair quote. • Honest advice whether repair is worthwhile versus replacement. • Experience with Rinnai continuous flow units preferred. Please note: We are NOT seeking replacement quotes at this stage. We are specifically looking for fault diagnosis and repair assessment before considering replacement options. Property is a rental in st kilda. Please quote: • Call-out fee. • Diagnostic fee. • Earliest availability. Photos attached.

Need a licensed plumber/electrician (or someone qualified) to help install and connect 2 commercial hot water machines at 2 different Melbourne CBD locations. Tasks required: * Connect water inlet/outlet for both machines * Connect and check drainage if required * Connect/install 16A power plug Machines are brand new and onsite. Locations: * 203 Elizabeth St, Melbourne CBD * 249 Lonsdale St, Melbourne CBD

My hot water system decided to not to play nice and stop working as I moved in. I have bought a new hot water system. Need the other one disconnected and this one connected. Both natural gas hot water systems. Approval for it to be externally put on the wall.

I need someone to come and connect my dishwasher and washing machine too hot water. We just moved into a rental and were unable to connect ourselves but it does exist.

I have a client that has a hot water heater not working. They need someone to come out today. My plumber is not available. Need someone to come

Bosch instantaneous gas hot water unit leaking from internal white plastic water flow valve / water assembly underneath unit. Slow drip even when taps off. Still working well but need the drip sorted.

I’m having an issue with the electric hot water system in my apartment (Stiebel Eltron DEL18AU). The shower and all taps are only producing cold water. I’ve tried troubleshooting it several times by turning off the MCB and then resetting the heater. It worked again about two weeks ago, but now it’s gone back to cold water only, and this time I can’t get it to heat up at all. The display still shows 50 (Celcius; max temp), but no hot water coming out.

The bathroom sink tap is not releasing any hot water. Cold water is working normally, but the hot water does not come through when the tap is turned on.

I have a Rinnai Solar 26 gas instantaneous hot water unit and the hot water is barely above warm. I have tried adjusting the dip switches as per the manual but it hasn't helped. I'm looking for a qualified plumber who can get hotter water out of this unit. As I have already tried the dip switches, please don't come if that is your only solution.

Gas not working for hot water need someone to come and take a look asap

Unit is under a cupboard and needs to be taken out to access it. Have no idea how to take the cupboard out.

We would like to replace the tap for the kitchen sink as the existing one is spraying. The hot water connection to the tap also appears to have a small leak which we presume would be repaired when a new tap is installed.

This hot water tap is preventing me from putting a dryer on top of my washing machine. I need it removed and capped off (doesn't need to look a specific way).

My gas storage hot water system (AquaMax 390SS-NG) has stopped producing hot water. The pilot light will not ignite. What’s happening: • The pilot is out and won’t relight • The red igniter button clicks, but there is no visible spark • Not sure if pilot gas is flowing • The big control dial turns, but pilot position isn’t responding normally • No flame appears at all

I am seeking a licensed plumber to install a Rinnai B26 continuous flow gas hot water system onto a steel fence located in an outdoor apartment courtyard. Scope of Works: Install new Rinnai B26 unit (**UNIT WILL BE SUPPLIED BY OWNER**). 240 volt Power Supply already available and located at installation point. Extend existing 32mm gas copper line approximately 10 metres from garage (ground floor basement) to new unit location in external courtyard (Level 1). Gas line to run from basement to courtyard via pre-prepared penetration hole. **Please note GAS FITTING work will be required** by a Certified Plumber. Plumber will be required to provide VBA LICENSE before job offer is approved. Seal penetration point with silicone to prevent water ingress into garage. Connect to existing 20mm PEX hot and cold water lines (already installed by previous plumber). Commission system and ensure correct operation. Additional Requirements: Licensed and insured plumber only Provide Compliance Certificate / Gas Safety Certificate suitable for Body Corporate All works to comply with relevant Australian Standards and regulations Please provide: Quote including labour and materials (excluding unit) Date of Installation If site needs to be inspected before commencement of works, I can arrange for this to occur. Thanks, Federico

Relocate hot water unit from internal to external. Opposite wall Power disconnected

hot water isolation valve needs replacing under kitchen sink, no longer functioning. Kitchen mixer tap replacement (supplied)

The hot water pipe connection has cracked and is leaking. It needs to be replaced. As show in the photos.

Replace continuous hot water unit for one bedroom apartment. i need the job done by Monday 19th afternoon . See pictures of unit for details. Also need a very minor leak fixed under sink. Thanks.

Looking for someone to get an existing Aquamax gas hot water unit up and running. Was working pre-Christmas just hasn’t been turned back on as it was switched off. Current status: • Pilot light is on and working • Water supply is on and running • Power is on and active It should be a quick and straightforward job for someone familiar with these systems — likely just final setup / adjustment. Photos attached for reference. Location: Brunswick Flexible timing. Please comment with experience and availability.