Find a professional hot water system contractor in Melbourne

A plumber recently replaced our 275L rheem gas hot water system with a Vulcan 170L gas storage water heater. We didnt realise until the job is completed. Its a hostel with 14 rooms and 8 bathrooms so this 170L is not going to be able to support it. We are looking for a plumber who can install another vulcan 170K to link with the existing 170K to double the capacity? and also to insure against breakdown of one of the unit in future. Is this doable? please quote? richmond location

The hot water in my flat running out rapidly snow down,about 1minute it became very small , the water pressure getting down.

shower water is not hot enough, but just warm. other taps for the kitchen, toilet etc only cold water.

Hello. Seeking quote for replacement of a shower head [one with a hose] and also a hot water system check. Professional experience required. Looking for a booking availability between July 6-10th. Location is Melbourne CBD.

Plumber wanted for Hot Water System and Water Pump. I need a Plumber fix my Hot Water System and my Water Pump for my Food Van. My Food Van had a private permanate site. So the owner of the food truck site took my Water Pump and he wanted to make my water run through the site watering system at site. I need a quote for this to to be done

N water coming out of cold water tap in kitchen. Hot tap is fine. All other taps, shower, bathroom, toilet fine. Blocked valve? I'm interstate and cannot fix. Daughter and brother have no clue. Can't supply an image as I'm not there.

want to replace old leaking gas hot water storage unit with new gas instant hot water service. Would also like price comparison if to convert to electric instant hot water.

Hot water supply disruption.

Hi there My brivis digital screen for my ducted heating isn’t working and I’ve checked my fuse board and nothing has turned off! Free today or tomorrow morning I’m unable to use the touch pad to use my ducted

I need someone to come and connect my dishwasher and washing machine too hot water. We just moved into a rental and were unable to connect ourselves but it does exist.

I have a client that has a hot water heater not working. They need someone to come out today. My plumber is not available. Need someone to come

I have a Rinnai Solar 26 gas instantaneous hot water unit and the hot water is barely above warm. I have tried adjusting the dip switches as per the manual but it hasn't helped. I'm looking for a qualified plumber who can get hotter water out of this unit. As I have already tried the dip switches, please don't come if that is your only solution.

Unit is under a cupboard and needs to be taken out to access it. Have no idea how to take the cupboard out.

We would like to replace the tap for the kitchen sink as the existing one is spraying. The hot water connection to the tap also appears to have a small leak which we presume would be repaired when a new tap is installed.

This hot water tap is preventing me from putting a dryer on top of my washing machine. I need it removed and capped off (doesn't need to look a specific way).

My gas storage hot water system (AquaMax 390SS-NG) has stopped producing hot water. The pilot light will not ignite. What’s happening: • The pilot is out and won’t relight • The red igniter button clicks, but there is no visible spark • Not sure if pilot gas is flowing • The big control dial turns, but pilot position isn’t responding normally • No flame appears at all

I am seeking a licensed plumber to install a Rinnai B26 continuous flow gas hot water system onto a steel fence located in an outdoor apartment courtyard. Scope of Works: Install new Rinnai B26 unit (**UNIT WILL BE SUPPLIED BY OWNER**). 240 volt Power Supply already available and located at installation point. Extend existing 32mm gas copper line approximately 10 metres from garage (ground floor basement) to new unit location in external courtyard (Level 1). Gas line to run from basement to courtyard via pre-prepared penetration hole. **Please note GAS FITTING work will be required** by a Certified Plumber. Plumber will be required to provide VBA LICENSE before job offer is approved. Seal penetration point with silicone to prevent water ingress into garage. Connect to existing 20mm PEX hot and cold water lines (already installed by previous plumber). Commission system and ensure correct operation. Additional Requirements: Licensed and insured plumber only Provide Compliance Certificate / Gas Safety Certificate suitable for Body Corporate All works to comply with relevant Australian Standards and regulations Please provide: Quote including labour and materials (excluding unit) Date of Installation If site needs to be inspected before commencement of works, I can arrange for this to occur. Thanks, Federico

Relocate hot water unit from internal to external. Opposite wall Power disconnected

hot water isolation valve needs replacing under kitchen sink, no longer functioning. Kitchen mixer tap replacement (supplied)

The hot water pipe connection has cracked and is leaking. It needs to be replaced. As show in the photos.