Find a professional hot water system contractor in Melbourne

Need a licensed/registered Victorian plumber/gasfitter to supply and install a compliant safety tray and Mildred sensor/valve under our internal gas hot water system and to provide a certificate of compliance confirming that the gas hot water system complies with standard AS/NZS 5601. Details: - Unit: Rheem 300170 (170L internal natural gas storage) - Location: internal cupboard, ground floor (see pictured) Please exclude parts/materials from your quote and note the cost of those in the comments.

Need a licensed plumber/electrician (or someone qualified) to help install and connect 2 commercial hot water machines at 2 different Melbourne CBD locations. Tasks required: * Connect water inlet/outlet for both machines * Connect and check drainage if required * Connect/install 16A power plug Machines are brand new and onsite. Locations: * 203 Elizabeth St, Melbourne CBD * 249 Lonsdale St, Melbourne CBD

I’m having an issue with the electric hot water system in my apartment (Stiebel Eltron DEL18AU). The shower and all taps are only producing cold water. I’ve tried troubleshooting it several times by turning off the MCB and then resetting the heater. It worked again about two weeks ago, but now it’s gone back to cold water only, and this time I can’t get it to heat up at all. The display still shows 50 (Celcius; max temp), but no hot water coming out.

I have a Rinnai Solar 26 gas instantaneous hot water unit and the hot water is barely above warm. I have tried adjusting the dip switches as per the manual but it hasn't helped. I'm looking for a qualified plumber who can get hotter water out of this unit. As I have already tried the dip switches, please don't come if that is your only solution.

Gas not working for hot water need someone to come and take a look asap

Hot water tank pipe burst, probably due to earth movement. Will require someone to fix and replace pipe.

Hot water not available in the shower Other taps all good

Unit is under a cupboard and needs to be taken out to access it. Have no idea how to take the cupboard out.

Bosch Condens 5000W combi boiler. Central heating ignites and works normally. Hot water tap demand does not trigger ignition/clicking. Suspect DHW flow sensor or diverter valve.

We would like to replace the tap for the kitchen sink as the existing one is spraying. The hot water connection to the tap also appears to have a small leak which we presume would be repaired when a new tap is installed.

This hot water tap is preventing me from putting a dryer on top of my washing machine. I need it removed and capped off (doesn't need to look a specific way).

My gas storage hot water system (AquaMax 390SS-NG) has stopped producing hot water. The pilot light will not ignite. What’s happening: • The pilot is out and won’t relight • The red igniter button clicks, but there is no visible spark • Not sure if pilot gas is flowing • The big control dial turns, but pilot position isn’t responding normally • No flame appears at all

I am seeking a licensed plumber to install a Rinnai B26 continuous flow gas hot water system onto a steel fence located in an outdoor apartment courtyard. Scope of Works: Install new Rinnai B26 unit (**UNIT WILL BE SUPPLIED BY OWNER**). 240 volt Power Supply already available and located at installation point. Extend existing 32mm gas copper line approximately 10 metres from garage (ground floor basement) to new unit location in external courtyard (Level 1). Gas line to run from basement to courtyard via pre-prepared penetration hole. **Please note GAS FITTING work will be required** by a Certified Plumber. Plumber will be required to provide VBA LICENSE before job offer is approved. Seal penetration point with silicone to prevent water ingress into garage. Connect to existing 20mm PEX hot and cold water lines (already installed by previous plumber). Commission system and ensure correct operation. Additional Requirements: Licensed and insured plumber only Provide Compliance Certificate / Gas Safety Certificate suitable for Body Corporate All works to comply with relevant Australian Standards and regulations Please provide: Quote including labour and materials (excluding unit) Date of Installation If site needs to be inspected before commencement of works, I can arrange for this to occur. Thanks, Federico

Relocate hot water unit from internal to external. Opposite wall Power disconnected

hot water isolation valve needs replacing under kitchen sink, no longer functioning. Kitchen mixer tap replacement (supplied)

Installation of hot water service

Supply of Rinnai b26, delivery, purchase of extention cord and valves for hot water service

The hot water pipe connection has cracked and is leaking. It needs to be replaced. As show in the photos.

Replace continuous hot water unit for one bedroom apartment. i need the job done by Monday 19th afternoon . See pictures of unit for details. Also need a very minor leak fixed under sink. Thanks.

Looking for someone to get an existing Aquamax gas hot water unit up and running. Was working pre-Christmas just hasn’t been turned back on as it was switched off. Current status: • Pilot light is on and working • Water supply is on and running • Power is on and active It should be a quick and straightforward job for someone familiar with these systems — likely just final setup / adjustment. Photos attached for reference. Location: Brunswick Flexible timing. Please comment with experience and availability.