Find a professional hot water system contractor in Melbourne

Hot water in apartment is not working properly, only gets lukewarm. Suspected TMV issue and may need replacement. It has been repaired/replaced a couple of times before but has stopped working again after around 7 months. Melbourne CBD based. Need fixed ASAP. Arrive after 10am, finish before 3pm.

plumber needed to turn pilot light on on hot water system. Seems like the ignitor switch not working. Need asap pls. Location Clayton

Hot water in apartment is not working properly, only gets lukewarm. Suspected TMV issue and may need replacement. It has been repaired/replaced a couple of times before but has stopped working again after around 7 months. Melbourne CBD based. Need fixed ASAP.

My hot water system decided to not to play nice and stop working as I moved in. I have bought a new hot water system. Need the other one disconnected and this one connected. Both natural gas hot water systems. Approval for it to be externally put on the wall.

I need someone to come and connect my dishwasher and washing machine too hot water. We just moved into a rental and were unable to connect ourselves but it does exist.

I have a client that has a hot water heater not working. They need someone to come out today. My plumber is not available. Need someone to come

Bosch instantaneous gas hot water unit leaking from internal white plastic water flow valve / water assembly underneath unit. Slow drip even when taps off. Still working well but need the drip sorted.

Need a licensed plumber/electrician (or someone qualified) to help install and connect 2 commercial hot water machines at 2 different Melbourne CBD locations. Tasks required: * Connect water inlet/outlet for both machines * Connect and check drainage if required * Connect/install 16A power plug Machines are brand new and onsite. Locations: * 203 Elizabeth St, Melbourne CBD * 249 Lonsdale St, Melbourne CBD

I’m having an issue with the electric hot water system in my apartment (Stiebel Eltron DEL18AU). The shower and all taps are only producing cold water. I’ve tried troubleshooting it several times by turning off the MCB and then resetting the heater. It worked again about two weeks ago, but now it’s gone back to cold water only, and this time I can’t get it to heat up at all. The display still shows 50 (Celcius; max temp), but no hot water coming out.

I have a Rinnai Solar 26 gas instantaneous hot water unit and the hot water is barely above warm. I have tried adjusting the dip switches as per the manual but it hasn't helped. I'm looking for a qualified plumber who can get hotter water out of this unit. As I have already tried the dip switches, please don't come if that is your only solution.

Unit is under a cupboard and needs to be taken out to access it. Have no idea how to take the cupboard out.

We would like to replace the tap for the kitchen sink as the existing one is spraying. The hot water connection to the tap also appears to have a small leak which we presume would be repaired when a new tap is installed.

This hot water tap is preventing me from putting a dryer on top of my washing machine. I need it removed and capped off (doesn't need to look a specific way).

My gas storage hot water system (AquaMax 390SS-NG) has stopped producing hot water. The pilot light will not ignite. What’s happening: • The pilot is out and won’t relight • The red igniter button clicks, but there is no visible spark • Not sure if pilot gas is flowing • The big control dial turns, but pilot position isn’t responding normally • No flame appears at all

I am seeking a licensed plumber to install a Rinnai B26 continuous flow gas hot water system onto a steel fence located in an outdoor apartment courtyard. Scope of Works: Install new Rinnai B26 unit (**UNIT WILL BE SUPPLIED BY OWNER**). 240 volt Power Supply already available and located at installation point. Extend existing 32mm gas copper line approximately 10 metres from garage (ground floor basement) to new unit location in external courtyard (Level 1). Gas line to run from basement to courtyard via pre-prepared penetration hole. **Please note GAS FITTING work will be required** by a Certified Plumber. Plumber will be required to provide VBA LICENSE before job offer is approved. Seal penetration point with silicone to prevent water ingress into garage. Connect to existing 20mm PEX hot and cold water lines (already installed by previous plumber). Commission system and ensure correct operation. Additional Requirements: Licensed and insured plumber only Provide Compliance Certificate / Gas Safety Certificate suitable for Body Corporate All works to comply with relevant Australian Standards and regulations Please provide: Quote including labour and materials (excluding unit) Date of Installation If site needs to be inspected before commencement of works, I can arrange for this to occur. Thanks, Federico

Relocate hot water unit from internal to external. Opposite wall Power disconnected

hot water isolation valve needs replacing under kitchen sink, no longer functioning. Kitchen mixer tap replacement (supplied)

Installation of hot water service

Supply of Rinnai b26, delivery, purchase of extention cord and valves for hot water service

The hot water pipe connection has cracked and is leaking. It needs to be replaced. As show in the photos.