Find professional window and door services in Reservoir VIC

Installation of a bifolding door

oilet sliding door stuck. Upper roller fitting loose.

My client needs this bedroom door replaced. We believe it would be a standard size however are unsure and unable to confirm. Photos of door attached.

I need to fit 5 door handles and make sure door will close in the frame. Currently the doors won’t fully close.

Supply and Install 2x internal doors including weather seals, automatic drop seal and a soft close latch Doors need to be solid core. First entrance - width is 0.824m, H 2.035m Second entrance - width is 0.770, H 2.043m

The installation on aluminium Door.3 Handles of 600mm single side doors,and one automatic door closer

Need to install doors for two internal closets. The closets are not standard size so the doors (standard size from Bunnings) will need to be trimmed by 1cm each on the width. We need handles attached to the doors too. This needs to be done before 5 June.

Need fixing: 1 door to fix by screwing the nails(its fallen off),fix sliding cupboard - it needs to be attached. Did a DIY installment on new toilet seats - needs to be adjusted properly as the screws are loose. Toilet gets blocked every now and then - need someone to put through the silver snake as the first initial DIY fix. Should take more than 1 hour?

Hi Richard, looking for a barn door to be installed in my garage wall opening. Would like Bunnings timber cladding to be mounted to the side of the door that’s facing the exterior/outside. Opening that needs to be covered is 3.47m - have found a 4m hardware set for $90.99. Would you be able to help me install ?

Looking to remove the doggy door from these sliding doors and replace the glass if possible - open to all offers.

I will have the door and hinges provided just need someone to come trim and install the door

The current door handles replaced the original door handles about 12 months ago, but as the doors are old, the handles are positioned at non standard height. I am seeking someone to lower the existing handles (1 x privacy and 3 x passage) to standard height and patch the original holes to a paint-ready finish (painting not required).

I need about 6 doors sanded back to original state. This also includes remove paint off of the glass panels. I don’t have much space at home to sand them, but I have a nature strip and live on a park which mean the job can possibly be done from my home, or happy for them to be taken to another location to be done.

Install a new 5.12m wide by 2.4m high bifold door. The door has been delivered in pieces brand new. I’ll be onsite to help, have helped install a few previously but need someone to lead it.

I am after getting a new, unmodified exterior door installed in place of an existing door. On top of this, I would like to get a doggy door installed on the new door. I am able to provide the materials (see picture). The hardware/fittings of the previous door must be transferred to the new door. This includes a knob and a deadlock. The door measures 2040 x 820 x 35. At the end of the work, there would be a new door installed, which includes a doggy door. Price is fairly flexible.

Seeking a handyman/locksmith to replace my front door handle/lockset. I’ve already purchased the new handle. The new handle is slightly longer than the existing one, so it will require drilling 2 new holes (approx. 2cm offset) and installing the new hardware properly. This is for an external front door, so alignment is important to ensure the door closes and locks smoothly with the existing latch/strike plate. What’s needed: - Drill new holes and install new handle/lockset - Ensure proper alignment and smooth operation Flexible with timing but the sooner the better ideally - Adjust latch/strike plate if required

Help with reversing internal bedroom door swing (open outward instead of inward). Including moving hinges, fill hole make shifting strike plate etc

My Front door made of thin plywood was kicked, it didn’t go through. So no hole but there’s 2 sort of like big raised cracks about 30cm long now, I just want them filled in and painted to match the door for a real estate inspection on Friday. (Doesn’t need to be A++ job but just fill in the cracks and a coat of paint. It’s like a shade of eggshell, sort of yellowy on an old front door. Even if you can Just match the patch already on the door to the left of the cracked area and I could possibly paint it myself. Thanks. Available today (Monday any time) tues + wed after 4pm & all day Thursday or Friday before 11am

Sliding doors to clinic rooms keep getting stuck inside cavity, need someone to fix them not sure what the issue is, if its the cavity itself or the tracks

This door will need new wheels as it’s not running on the track properly, I thought it was a track problem but I’m sure the wheels are broken - looking for the best price to get this fixed