Find an experienced handyman in South West Sydney

Nee 55mm cornice for 5120mm length. Plus half metre return on one side as cornice is damaged there. Need to sheet small gap between existing ceiling and beam so cornice can sit correctly. Needs to be patched and ready for paint As per photos half the length is over the 60mm for the cornice. Happy to get inspection and quote at job for certainty

Looking for someone to correctly install my current lock and deadbolt. Please provide a written quote first. Work will proceed once approved. The lock I currently installed … it works but not aligned properly, there is a gap and some movement. If this lock cannot be fitted securely, I’m open to reinstalling the original lock instead.

“Fix exterior wall cracks, patch render, waterproof and repaint small area. Located Fairfield NSW. Photo attached.” Tasks: – Fill small cracks – Patch small damaged render area – Apply waterproof sealer – Repaint small section - Check/seal bottom of the wall Area is small. Budget around $600–$1000. Looking for experienced handyman with good reviews.”

Backyard slide door has to be fixed Door lamp that came off as basket ball hit it. Needs to be re-screed back

Need to install curtains and blinds for new house

Gyprock to be sealed in the media room. Have small 5-6 patches to be closed

I need a gyprock wall cut as an arch style walk way for my store. Send me quotes. I’ve attached a picture of the wall and a generated image of something I want. Also removal of waste from the job.

Install garden shed 2.26 x 1.52 x 1.80m. Will supply material as required.

Gyprock / Fibre Cement Ceiling Installation – Balconies & Porch I’m looking for an experienced gyprocker to install ceiling linings using 6mm fibre cement sheets to the following areas: 2X - external balconies (curved) - front porch area (Curved) - 600mm x 2000mm (rectangle) Scope of works: - Install 6mm fibre cement sheets to ceilings - Form 10mm express joints using black backing strip (materials supplied onsite) - Apply the black strip 10mm expressed joints to all corners for a clean architectural finish - Set out and align joints consistently across all areas - Fix, cut, and install sheets to a high standard, ready for finishing Materials: - All materials are supplied onsite (including black strip for express joints)

Ready to install. Toal of 8 blinds for windows as well as 10 tracks for the curtains

Instal Permachild Baby Swing Gate for hallway - requires drilling

The bidet toilet seat was installed last night but it is slightly askew and needs to be corrected. Also the pipes are leaking and will need to be tightened or adjusted.

Install approx 18LM of 90mm cove cornice. internal corners = 7 External corners = 6 End infill = 3 Material supply and install to be agreed on Note walls and ceilings may not be flat, level or plumb.

I’m looking to replace the current small chandelier above the stairwell with a new chandelier. Photos of the existing fixture and the new replacement light are attached for reference. I can provide the installation manual or any additional details if needed. Open to offers.

Cornice has bubbled up. As pic. One cornice is smaller than the other

Need a handyman to 1. fix kitchen drawer. Sliding bracket has been Detached. 2. Fix sliding door. There are 3 glass doors. 1st door slides open but middle glass door seems to be stuck.

There’s small damage on one of the wall. Need someone to patch the whole with new Gyprock and repaint the area. Photos can be sent.

Need large clock, hung up on wall above TV ,also need hose reel hung and connected to outside brick wall

Need someone to Assemble Mobile Scaffolding . Already delivered onsite.

Task Description: Looking for a reliable person to assemble a new Keter Darwin 6x4 plastic garden shed. The work is located in. Video : http://www.youtube.com/watch?v=dfq4rz80Mgg Key Requirements & Steps (Detailed Scope of Work): Step 1: Land Preparation (Critical): Step 2: Shed Base Assembly: Connect the two-part plastic base and secure it with the initial screws once the ground is level. Step 3: Panel Installation: Slot in the ~20 plastic panels, including corners and back pieces. Step 4: Roof Assembly: Assemble the two-piece roof with the strengthening bar and center joining strip. This part requires perseverance and detail to ensure it is watertight. Step 5: Door & Hardware: Install the two doors, including the hinges and the locking mechanism, which can be a bit fiddly and requires manual assembly. Correct ground leveling is essential to prevent doors from misaligning. Step 6: Fixings: There are hundreds of screws involved in this build to fully secure the joints and the base. Keter Storage Shed Shelf Kit × 1 needs to be installed inside at the end Tools Needed: Shovel/Rake/Levelling tool (for land prep). Electric Drill/Driver (highly recommended due to the large number of screws). A ladder for reaching the roof panels. Additional Details: Location: [ Austral/Sydney NSW 2179] Timing: Flexible, but would prefer completion in a single session, given the sequential nature of the ground-to-shed build. Pro-tip from the video for the Tasker: If you find the hinge holes difficult to line up, try driving a "pilot" screw in and back out first to clear the path. Please also ensure the outer door trims are perfectly aligned so the doors shut correctly.