Book a professional blind repair service in Melbourne

My blind has fallen down. It’s a long wooden rod but there’s currently nothing satisfactory on either end to hold it in place. I’m looking for someone to: * Assess what’s needed (likely small brackets/hooks or similar) * Supply or recommend the right fix * Install it so the blind sits securely again It’s not a complicated job, just a bit fiddly and needs someone who can come with a practical solution. Flexible with timing. Please bring tools and any basic hardware that might be needed.

Bedroom blind won't pull up on one side

Existing blind, blind lost its tension and unrolling on its own - Requires repair or replacement part see photos of existing roller component. And re-hung

Cut down 5 blinds to fit window

Blind installation in a bedroom

Blind’s mechanism for adjusting the angle of the slats has broken or disconnected.

Large new bedroom blockout blind needs to be installed (replace old blind). It’s a new stick n fit install see photos and instructions. It’s an easy job but because of the size will need two people. Blind is 200cm wide and 300cm floor to top of blind - photos are of the old blind

The cord on my roller blinds has slipped off

I need someone to help reinstalling roller blinds and curtain rods that were removed during some door repairs.

The window width is 3.8m. Need to remove 3 roller blinds attached to each window and replace with single curtain track

The chain on my roller blinds isn’t working properly

I need a Coolaroo outdoor blind from Bunnings installed on my apartment balcony. It’s a recessed, semi-enclosed balcony and the blind will be mounted inside the balcony opening. This is the blind (but in the darker colour) https://www.bunnings.com.au/coolaroo-2-4-x-2-4m-graphite-crank-operated-outdoor-blind_p0334441. It will leave a gap either side of the opening, hoping to get these as equal as possible. You will need a step ladder, appropriate drills bits for masonry/metal. I have attempted to install myself and failed! All but one part is missing (a plastic wall anchor). Happy to send more photos if required.

I have a roller blind with a chain that has come off the track that needs repair

Blind feel to ground . The glue weakened a bit. Needs to be restuck.

I have a blockout blind that has fallen off it's holder. It's a really easy job, just requiring someone with a ladder to drop in and put it back up. I've done this before myself, but I'm not in the country right now. Can someone local drop in and fix it? Should take all of 5 minutes. Josh

Metal beaded chain on my roller blind has snapped and the blind won’t roll up/down properly on two sets of blinds. Looking for someone to: • Replace the chain and/or clutch mechanism • Ensure blind rolls smoothly and is reinstalled correctly Blind is mounted high (loft ceiling) so a tall ladder will be required.

Looking for a Handy Person This Weekend I need a very small blind installed on a kitchen window (approx. 1.20 m wide/1.5m height) inside the frame or (1.35m) outside frame and 3–4 safety anchors fitted for blind cords in the same property. You will need to get product from spotlight or bunnings - we will reimburse purchase as well. Should be under $50 according to my research. Beige, oak preferred, but do not mind. Would love for the work to be done this weekend. Please get in touch if you can help. Thank you!

The string bead has come completely out of the track, need someone to fix it.

I purchased the blind below and need it to be hung in the kitchen window. It is too large to sit flush inside the window frame so will need to be drilled in to the wooden window frame https://www.spotlightstores.com/blinds/roller-blinds/double-roller-blinds/selections-dual-roller-blind/80425615?utm_source=spotlight-system&utm_medium=email&utm_campaign=ord-conf&utm_term=prod&utm_content=body

One of our blinds doesn’t grip well as you roll it down. When you roll it down past the half way mark it begins to tumble down to the ground. So for example you can’t have it rolled 3/4 of the way down as it’ll just tumble all the way down. Hoping there’s someone that knows how to repair this rather than go for a replacement? I have attached pictures but I also have a video I can send that demonstrates this